1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Aflickted
    Thread

    Unresolved Gcode Question

    G90 M82 M106 S0 M140 S55 M190 S55 M104 S195 T0 M109 S195 T0 G28 G29 ; autolevel G92 E0 G1 E-1.0000 F1800 G1 Z1.400 F1000 ; process Process1 ;...
    Thread by: Aflickted, Jan 11, 2018, 69 replies, in forum: Troubleshooting
  2. Aflickted
    Thread

    Solved What could be causing this?

    I’m at my wits end trying to figure this out. It’s random when it does it but does it on every print. Temp doesn’t change it. Calibrated...
    Thread by: Aflickted, Jan 7, 2018, 39 replies, in forum: Troubleshooting
  3. Aflickted
    Thread

    Solved Very rough, bumpy 1st layers

    [IMG] Hatchbox filament PLA 192 degrees Heated bed 55 degrees I installed a E3Dv6 and started having this problem. Very rough layers for the...
    Thread by: Aflickted, Dec 10, 2017, 2 replies, in forum: General Questions
  4. Aflickted
    Thread

    Unanswered Need help filling the gap!

    [IMG] Any way to fill these gaps? I’m using Simplify3D. This is the print preview. I’m trying to make some cookie cutters and I need them as...
    Thread by: Aflickted, Oct 23, 2017, 13 replies, in forum: General Questions
  5. Aflickted
    Thread

    Answered Move y axis after print is finished

    This is what is have in my END GCODE. I need my Y axis to move out but it moves in after the print is done. I think i need to change the G28(home)...
    Thread by: Aflickted, Jul 6, 2017, 4 replies, in forum: Troubleshooting
  6. Aflickted
    Thread

    Solved Gears flaking

    Got another small problem. The gears are kind of "shaving" off. Leaving dust all over the place. Sent from my iPhone using Tapatalk
    Thread by: Aflickted, Jun 28, 2017, 18 replies, in forum: Troubleshooting
  7. Aflickted
    Thread

    Solved Weird noise in filament gear

    While printing, the filament gear/motor is making a weird chirping noise when it stops or maybe retracts. I'm uploading a video. Pay attention to...
    Thread by: Aflickted, Jun 14, 2017, 17 replies, in forum: Troubleshooting
  8. Aflickted
    Thread

    Solved Concaved print

    Hello guys. So I'm trying to print this disc. PLA Hotend 185 degrees Heated bed 60 degrees. About .30 inch thick 10% infill E3D-V6 hotend...
    Thread by: Aflickted, Jun 8, 2017, 25 replies, in forum: Troubleshooting
  9. Aflickted
    Thread

    Solved Attaching magnets to heat bed

    What would I use to attach magnets to the heat bed? I got a replacement bed and the magnets didn't come installed on the bed. Thanks in advance!
    Thread by: Aflickted, May 17, 2016, 4 replies, in forum: General Questions
  10. Aflickted
    Thread

    Solved Warping using ABS, please advise.

    Hatchbox ABS red filiment Hotend 237 Bed 95c Robo R1 E3dv6 hotend Print time about 3 hours I'm printing this box and it keeps warping on me....
    Thread by: Aflickted, May 3, 2016, 6 replies, in forum: General Questions
  11. Aflickted
    Thread

    Unresolved What cause this in the print?

    I was having some trouble with the layer height in my new printer. It printed a few parts very nice. Then it started not extruding. So I thought.....
    Thread by: Aflickted, Apr 17, 2016, 9 replies, in forum: Troubleshooting
  12. Aflickted
    Thread

    Solved What cause this in the print?

    I was having some trouble with the layer height in my new printer. It printed a few parts very nice. Then it started not extruding. So I thought.....
    Thread by: Aflickted, Apr 17, 2016, 2 replies, in forum: Troubleshooting
  13. Aflickted
    Thread

    Unanswered Extruder won't heat up.

    MC says the temp is at 220 degrees always and I set it at 210. It then has the arrow going down but never goes down to 210 and stays at 220, but...
    Thread by: Aflickted, Mar 29, 2016, 94 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again