1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 8
  1. John in MS
    Post

    Answered Robo R1 - Z not moving up during print

    Z steps in my little LCD controller days .0800. I don't play around with my firmware much. Should I flash it?
    Post by: John in MS, Dec 15, 2018 in forum: Troubleshooting
  2. John in MS
    Post

    Answered Robo R1 - Z not moving up during print

    I have the plus. I will look into this
    Post by: John in MS, Dec 15, 2018 in forum: Troubleshooting
  3. John in MS
    Thread

    Answered Robo R1 - Z not moving up during print

    My Robo R1 z axis works great when I move it up and down manually when not printing. But when I begin printing I get a great first layer but...
    Thread by: John in MS, Dec 15, 2018, 7 replies, in forum: Troubleshooting
  4. John in MS
    Post

    Solved Is there an diagram on how the R1 extruder is assembled?

    [IMG] Is this it? Any special instructions in installing?
    Post by: John in MS, Nov 22, 2018 in forum: Troubleshooting
  5. John in MS
    Post

    Solved Is there an diagram on how the R1 extruder is assembled?

    [MEDIA] Thank you for the video I used it to come up with my current configeration. I thought I had something working and came home and found it...
    Post by: John in MS, Nov 21, 2018 in forum: Troubleshooting
  6. John in MS
    Post

    Solved Is there an diagram on how the R1 extruder is assembled?

    Finally had a chance to work on it again. The above diagram didn't show the R1 extruder. I need to post the order of parts I have on mine. I can...
    Post by: John in MS, Nov 21, 2018 in forum: Troubleshooting
  7. John in MS
    Post

    Answered Cracked my bed on my R1 Plus

    I cracked mine months ago. I have a sheet off cut glass from Lowes on to of mine now
    Post by: John in MS, Nov 17, 2018 in forum: Troubleshooting
  8. John in MS
    Thread

    Solved Is there an diagram on how the R1 extruder is assembled?

    I added a new heater wire to my E3DV6. While doing it I took apart the extruder to clean the hobbed bolt and cleaned all the loose shavings....
    Thread by: John in MS, Nov 4, 2018, 9 replies, in forum: Troubleshooting
  9. John in MS
    Post

    Answered Can Robo stock extruder hot end be used in E3DV6?

    Will be getting another hot wire that goes to the heat block. If I cut the included and make a quick connect, does positive and negative matter on...
    Post by: John in MS, Oct 27, 2018 in forum: Troubleshooting
  10. John in MS
    Thread

    Answered Can Robo stock extruder hot end be used in E3DV6?

    [IMG] [img] I have torn the wiring to the hot of my E3DV6. My problem with it is the constant need to remove clogs from heat creep. This is with...
    Thread by: John in MS, Oct 27, 2018, 4 replies, in forum: Troubleshooting
  11. John in MS
    Post

    Answered Y axis not homing correctly

    Ok. I will try. I saw a video with the same problem and it worked right after simply removing the xxl and running a print from the computer. Then...
    Post by: John in MS, Aug 1, 2018 in forum: Troubleshooting
  12. John in MS
    Post

    Answered Y axis not homing correctly

    When I start the Home with the bed fully in the front, it goes dead center. Then when I home from the middle, the bed moves completely forward and...
    Post by: John in MS, Jul 31, 2018 in forum: Troubleshooting
  13. John in MS
    Thread

    Answered Y axis not homing correctly

    [MEDIA] Y not moving back When I home. I just moved it work on the hotend. Thanks for any help
    Thread by: John in MS, Jul 31, 2018, 6 replies, in forum: Troubleshooting
  14. John in MS
    Post

    Answered Chunks of glass came off with print

    Thanks
    Post by: John in MS, Jul 23, 2018 in forum: Troubleshooting
  15. John in MS
    Post

    Answered Chunks of glass came off with print

    I just came from Lowes with a new plate of glass after cracking my bed. What changes if any would I make to my settings on my LCD full display...
    Post by: John in MS, Jul 23, 2018 in forum: Troubleshooting
  16. John in MS
    Post

    Partial Answer Heat creep in new E3DV6

    You know with my limited knowledge of firmware I think I did make that change. It would require me looking at it tonight to see I that change...
    Post by: John in MS, May 31, 2018 in forum: Troubleshooting
  17. John in MS
    Thread

    Partial Answer Heat creep in new E3DV6

    Well my frustration with the E3D install continues. Hopefully I can soon see the possible upsides of this hotend over the regular hex. I unhooked...
    Thread by: John in MS, May 31, 2018, 4 replies, in forum: Troubleshooting
  18. John in MS
    Thread

    Partial Answer Problems after installing E3DV6

    Thanks for the help Saturday night. I did have me thermistor and fan wire mixed up. It heats up fine. Other problems persists. I'm not...
    Thread by: John in MS, May 29, 2018, 1 replies, in forum: Troubleshooting
  19. John in MS
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Yes thank you it was wired wrong. Now bed ave extruder warm up. Started test print and the extruder motor is erratic. Either i plug it in...
    Post by: John in MS, May 26, 2018 in forum: Mods and Upgrades
  20. John in MS
    Post

    Community Favorite E3D v6 Information and Installation Guide

    [IMG] All connections seems to be tight and corrrect. Still zero reading. Must be a lemon
    Post by: John in MS, May 26, 2018 in forum: Mods and Upgrades
Showing results 1 to 20 of 145 Next >
Search Again
Page 1 of 8