1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 3
  1. Mike Toole
    Post

    Answered Filament sticks to nozzle

    I am no expert. Repeat, I am no expert, but I struggled with PET-g and had the same issues plus a few others. :) I ended up getting it to work...
    Post by: Mike Toole, Jul 28, 2017 in forum: Troubleshooting
  2. Mike Toole
    Post

    NinjaFlex filament

    link does not work any longer
    Post by: Mike Toole, Jun 20, 2017 in forum: Printing Filament
  3. Mike Toole
    Post

    Rubberized or rubbery feel filament, is there one?

    Well, ended up with Hatch box TPU. You were right, definitely harder to get set up properly. I am struggling to get good prints on simple parts...
    Post by: Mike Toole, Jun 10, 2017 in forum: Printing Filament
  4. Mike Toole
    Thread

    Rubberized or rubbery feel filament, is there one?

    I would like to design and print a phone case and would like to see if there is a rubbery feel or rubberized filament out there. been searching...
    Thread by: Mike Toole, Jun 5, 2017, 3 replies, in forum: Printing Filament
  5. Mike Toole
    Thread

    R2 ship backlog

    my work just ordered an T2 last Wednesday. Any idea about the shipment backlog?
    Thread by: Mike Toole, May 31, 2017, 20 replies, in forum: General Questions
  6. Mike Toole
    Post

    Dual Extrusion on Robo 3D R1

    We were comparing printers at work and one had the option of adding a second extruder. We do not have nor foresee using multiple materials or...
    Post by: Mike Toole, May 25, 2017 in forum: General Questions
  7. Mike Toole
    Post

    Dual Extrusion on Robo 3D R1

    thank you!
    Post by: Mike Toole, May 25, 2017 in forum: General Questions
  8. Mike Toole
    Post

    Dual Extrusion on Robo 3D R1

    Can a dual extrusion set up be used simultaneously to speed up printing? or is it a one extruder at a time type of printing?
    Post by: Mike Toole, May 25, 2017 in forum: General Questions
  9. Mike Toole
    Post

    Show us your best Robo 3d print

    [ATTACH] A part I print for work. 1/4 section at a time. 4.86" tall. Low quality 10% infill. PLA
    Post by: Mike Toole, May 24, 2017 in forum: Projects
  10. Mike Toole
    Post

    Filament Runout Sensor (FRS) upgrade to Robo R1/R1+

    Awesome! Thanks all. I just put the lcd screen on last night so I am not eager just yet to start messing with firmware. :) however, I will...
    Post by: Mike Toole, May 21, 2017 in forum: Mods and Upgrades
  11. Mike Toole
    Post

    Filament Runout Sensor (FRS) upgrade to Robo R1/R1+

    During the filament change routine, does the print head have to go to the home position? I would like to make these additions to my R1+....
    Post by: Mike Toole, May 20, 2017 in forum: Mods and Upgrades
  12. Mike Toole
    Post

    Considering buying a ROBO 3D R1+

    I am a brand new 3d printer guy with a week old R1+. Out of the box, followed the instructions and some of my nephew's recommendations and this...
    Post by: Mike Toole, May 19, 2017 in forum: General Questions
Find older messages
Showing results 41 to 52 of 52
Search Again
Page 3 of 3