1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Acclamator777
    Thread

    print not centered

    I just downloaded version 3.1 and my prints are starting at the front left of the bed and not center. Any thoughts to why this is happening
    Thread by: Acclamator777, Feb 28, 2018, 1 replies, in forum: Troubleshooting
  2. Acclamator777
    Thread

    CURA 3.1

    I just upgraded my cura software to the latest 3.1 version. I lost all my original G-code start up and end settings. Can somebody share your...
    Thread by: Acclamator777, Feb 22, 2018, 0 replies, in forum: Software
  3. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I added a belt tightener and it's printing great. Thanks you all for your help!
    Post by: Acclamator777, May 30, 2017 in forum: Troubleshooting
  4. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I replaced the stepper motor because it looked like the bearings were going out. I did a test print and all seemed ok.[ATTACH] I then tried the...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  5. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I will get to work on it! I will reply to let you know how things went and hopefully things will be working well. Thanks for the help!
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  6. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    Is it possible to replace the motor with one of the original Z axis motors I replaced with the lead screw upgrade kit? Or do I have to get a...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  7. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    IBelt seems to be ok but I took a look at the motor and noticed that it looks like fluid in the bottom hole of the stepper motor [ATTACH] and...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  8. Acclamator777
    Thread

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I just installed the lead screw upgrade kit on my refurbished R1. It prints out really good now. No more Z banding. But now I am encountering a...
    Thread by: Acclamator777, May 29, 2017, 11 replies, in forum: Troubleshooting
  9. Acclamator777
    Post

    Solved lead screw upgrade issues

    Having issues getting a video uploaded. Good news is I took a look at the stepper motor connections on the board underneath. I rotated the...
    Post by: Acclamator777, May 27, 2017 in forum: Troubleshooting
  10. Acclamator777
    Post

    Solved lead screw upgrade issues

    Sorry that it took so long to respond back. Here are pics of the left and right z switch lead screw upgrade assembly. Also, this is the...
    Post by: Acclamator777, May 25, 2017 in forum: Troubleshooting
  11. Acclamator777
    Post

    Solved lead screw upgrade issues

    Went to robo 3d firmware page and downloaded lead screw upgrade firmware.
    Post by: Acclamator777, May 25, 2017 in forum: Troubleshooting
  12. Acclamator777
    Thread

    Solved lead screw upgrade issues

    I have a refurbished R1 model and I just installed the lead screw upgrade. Pretty straight forward installation. I installed the lead screw...
    Thread by: Acclamator777, May 25, 2017, 10 replies, in forum: Troubleshooting
  13. Acclamator777
    Thread

    Answered Micro Swiss plated brass wear resistance nozzle issues

    After a year of printing on my R1 with good prints, I decided to replace the original nozzle with a Micro Swiss plated brass wear resistance...
    Thread by: Acclamator777, May 17, 2017, 2 replies, in forum: Troubleshooting
  14. Acclamator777
    Thread

    Answered OverHang tips and tricks

    I've been having issues with overhangs. Best example is the Benchy model. The bow always comes out looking not so great. My fans ( 2 ducted...
    Thread by: Acclamator777, Apr 17, 2017, 2 replies, in forum: Troubleshooting
  15. Acclamator777
    Post

    Solved fluctuating temperature reading

    Thanks for your input. I was thinking it might be the heater core. Just wanted someone elses opinion. Will place an order for a replacement...
    Post by: Acclamator777, Feb 25, 2017 in forum: Troubleshooting
  16. Acclamator777
    Thread

    Solved fluctuating temperature reading

    I've had my Robo 3D R1 for almost a year and I have found it to be a wonderful machine. Just recently, I've noticed that the temperature has been...
    Thread by: Acclamator777, Feb 25, 2017, 3 replies, in forum: Troubleshooting
  17. Acclamator777
    Post

    Unresolved Cura Bed Leveling Issues

    The sequence does work in matter control and my prints do come out good in cura. It's just that the bed leveling sequence starts off in the wrong...
    Post by: Acclamator777, Jun 7, 2016 in forum: Troubleshooting
  18. Acclamator777
    Post

    Unresolved Cura Bed Leveling Issues

    Nothing is blocking the printer head or bed that I can see. I watched the first video as you suggested and it's as if my bed leveling sequence...
    Post by: Acclamator777, Jun 7, 2016 in forum: Troubleshooting
  19. Acclamator777
    Thread

    Unresolved Cura Bed Leveling Issues

    I'm having issues with the start of a print. I am using the latest cura software. When the slicer program runs bed leveling X and Y axis are...
    Thread by: Acclamator777, Jun 6, 2016, 8 replies, in forum: Troubleshooting
  20. Acclamator777
    Thread

    Vertical Z Risers

    Not sure if anybody has come across this MOD I found on Thingiverse but it is interesting. A spacer to give your printer more printing space on...
    Thread by: Acclamator777, Apr 13, 2016, 1 replies, in forum: General Questions
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2