1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Michael Woodward
    Post

    Solved Bed Temp rises wildly after 15 min of constant temp.

    ok, i think i have found something. in the Configuration.h file there is a section where you define the motherboard # define MOTHERBOARD...
    Post by: Michael Woodward, Sep 3, 2019 in forum: Troubleshooting
  2. Michael Woodward
    Thread

    Solved Bed Temp rises wildly after 15 min of constant temp.

    I recently had to replace my RAMPS board on my Robo 3D R1 plus, because the bed heater wouldn't heat anymore. i found that the board was burned...
    Thread by: Michael Woodward, Sep 1, 2019, 3 replies, in forum: Troubleshooting
  3. Michael Woodward
    Post

    Solved After Merlin 1.1.9 upgrade, z axis will not raise in print

    so i think i solved this issue. the potentiometer on the stepper driver did not have a stopping point so i replaced this stepper driver with one...
    Post by: Michael Woodward, Sep 1, 2019 in forum: Troubleshooting
  4. Michael Woodward
    Post

    Solved After Merlin 1.1.9 upgrade, z axis will not raise in print

    Thanks for the education on this, so is the behavior i am seeing due to too little current on the stepper driver? or too much?
    Post by: Michael Woodward, Aug 20, 2019 in forum: Troubleshooting
  5. Michael Woodward
    Post

    Solved After Merlin 1.1.9 upgrade, z axis will not raise in print

    DEFAULT_ZJERK = 0.3 DEFAULT_MAX_ACCELERATION { 900, 900, 100, 10000 } so couple of questions about that: if it is a stepper issue...
    Post by: Michael Woodward, Aug 20, 2019 in forum: Troubleshooting
  6. Michael Woodward
    Thread

    Solved After Merlin 1.1.9 upgrade, z axis will not raise in print

    My original board burned up. replace it with a new RAMPS 1.4. put the original stock ROBO3DR1PLUSv2 firmware on it and the bed temp went crazy....
    Thread by: Michael Woodward, Aug 20, 2019, 8 replies, in forum: Troubleshooting
  7. Michael Woodward
    Post

    Chipped borosilicate glass bed with T-Glase

    So I found this install guide on their site. https://geckotek-test.myshopify.com/pages/robo3d-r1-magnetic-base-install-guide But in looking at...
    Post by: Michael Woodward, Dec 21, 2018 in forum: Troubleshooting
  8. Michael Woodward
    Post

    Chipped borosilicate glass bed with T-Glase

    I am in the same boat (chipped glass). I was thinking of replacing it with a Geckotech bed, but not sure of which one to get and in looking...
    Post by: Michael Woodward, Dec 21, 2018 in forum: Troubleshooting
  9. Michael Woodward
    Post

    E3D PT100, how to install and configure

    Would you be able to post some pics of what you ended up with? specifically how you added the 4x1 to the board.
    Post by: Michael Woodward, Apr 8, 2018 in forum: Mods and Upgrades
  10. Michael Woodward
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I just need to get it to 110 in the short term.
    Post by: Michael Woodward, Dec 20, 2017 in forum: Mods and Upgrades
  11. Michael Woodward
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Increasing the bed temp is all i need right now. I have been reading through all the past post about this new Marlin firmware and in looking at...
    Post by: Michael Woodward, Dec 20, 2017 in forum: Mods and Upgrades
  12. Michael Woodward
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Is this an update i can upload to a Robo 3d R1+ that has no other modifications except for additional fans? all i really need is to get past the...
    Post by: Michael Woodward, Dec 20, 2017 in forum: Mods and Upgrades
Showing results 1 to 12 of 12
Search Again