1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. kain0r3D
    Post

    Will this custom cooler fit with the stock hot end?

    Thanks Mark, is that what the R1+ comes with out of the box, an E3D?
    Post by: kain0r3D, Jul 7, 2019 in forum: Mods and Upgrades
  2. kain0r3D
    Thread

    Will this custom cooler fit with the stock hot end?

    This cooler from thingiverse is the type I'm after and I'm wondering if anyone can see why it wouldn't suit the stock hot end even though it's...
    Thread by: kain0r3D, Jul 7, 2019, 3 replies, in forum: Mods and Upgrades
  3. kain0r3D
    Post

    Solved Which Belt Tension technique/mod to use?

    Works perfectly. Just need a smaller screw...
    Post by: kain0r3D, May 9, 2017 in forum: Troubleshooting
  4. kain0r3D
    Post

    Solved Which Belt Tension technique/mod to use?

    Yeah I've got a really ghetto zip tie tightening thing going on but was hoping for something more elegant. Would this work?...
    Post by: kain0r3D, May 9, 2017 in forum: Troubleshooting
  5. kain0r3D
    Thread

    Solved Which Belt Tension technique/mod to use?

    Hey guys, Can I ask what you use to tighten up your x-axis belt? I wan't the easiest solution but there's so many online. Look forward to hearing...
    Thread by: kain0r3D, May 9, 2017, 11 replies, in forum: Troubleshooting
  6. kain0r3D
    Post

    Solved Drooping Heat Pad an issue?

    Yup, looks like just the cork. I'll tape it up! Cheers.
    Post by: kain0r3D, Dec 14, 2016 in forum: General Questions
  7. kain0r3D
    Thread

    Solved Drooping Heat Pad an issue?

    Hi all, The heating pad under my glass seems to be drooping off the glass in the middle slightly where it's not taped. Should I be concerned?...
    Thread by: kain0r3D, Dec 13, 2016, 3 replies, in forum: General Questions
  8. kain0r3D
    Post

    Full Graphic Display Controller enclosure mount

    Great design @3d_dan Just got my Full Graphic Controller and want to mount using your design however I can't for the life of me figure out how...
    Post by: kain0r3D, Jul 18, 2016 in forum: Mods and Upgrades
  9. kain0r3D
    Thread

    New filament interface for the R1+?

    Does anyone know of an r1+ version of this?: http://www.thingiverse.com/thing:889541 Combined with the quick release plate, removing stuck...
    Thread by: kain0r3D, Jul 7, 2016, 0 replies, in forum: Mods and Upgrades
  10. kain0r3D
    Post

    XXL screen availability

    I just ordered the one on eBay I listed, should be no dramas making the firmware change. Do you know if there would be any problems using an eyefi...
    Post by: kain0r3D, Jul 4, 2016 in forum: Mods and Upgrades
  11. kain0r3D
    Post

    XXL screen availability

    Is that this one? http://goo.gl/1eKOG6 Is that just plug and play with the current R1+ firmware?
    Post by: kain0r3D, Jun 28, 2016 in forum: Mods and Upgrades
  12. kain0r3D
    Thread

    XXL screen availability

    I'm chasing a plug and play screen to monitor SD card printing on my Robo3D R1 Plus. Everywhere seems to be sold out (XXL). Any idea where I...
    Thread by: kain0r3D, Jun 16, 2016, 8 replies, in forum: Mods and Upgrades
  13. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    YES!!!! Sorry @mark tomlinson I thought i'd made the switch extensions known. I added them as Ryan said, to allow clearance for the 40mm fan. I...
    Post by: kain0r3D, Jun 9, 2016 in forum: Troubleshooting
  14. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    Changing the build volume (x-axis) size or the origin offset on that screen has no effect on the auto-leveling. If I save changes in the machine...
    Post by: kain0r3D, May 18, 2016 in forum: Troubleshooting
  15. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    It's not a home switch issue, nothing is getting stuck. Here's a video of a G28 running followed by the G29. The G28 works fine, the G29 however...
    Post by: kain0r3D, May 18, 2016 in forum: Troubleshooting
  16. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    I've changed the dimensions of the bed in the settings, which are correct however the problem still exists where the bed leveling starts too far...
    Post by: kain0r3D, May 17, 2016 in forum: Troubleshooting
  17. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    Ok will do. In S3D, how can I change the dimensions of my bed to make it slightly smaller? The print head is ramming up against the right hand...
    Post by: kain0r3D, May 10, 2016 in forum: Troubleshooting
  18. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] What can you gather from that? I know that black wasn't the best...
    Post by: kain0r3D, May 10, 2016 in forum: Troubleshooting
  19. kain0r3D
    Post

    Unresolved My S3D first layer looks like a ballbag :/

    -0.19mm I've since changed that to -0.16. Is there a reasonably common test print model for first layers I can use moving forward to show...
    Post by: kain0r3D, Apr 21, 2016 in forum: Troubleshooting
  20. kain0r3D
    Post

    Unanswered LED's flickering during use. Power Supply issue?

    Yeah occasionally it will have an effect on the home theater although exactly which component I haven't bothered to pinpoint as it just cuts...
    Post by: kain0r3D, Apr 21, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2