1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. tom1441
    Post

    Partially Solved Bed level / uneven printing

    That helps me too thx
    Post by: tom1441, Aug 23, 2017 in forum: Troubleshooting
  2. tom1441
    Post

    Robo 3D r1 plus

    Do you have a link for the firmware
    Post by: tom1441, Aug 22, 2017 in forum: Projects
  3. tom1441
    Post

    Robo 3D r1 plus

    Thank you I will be replacing both ordered from robo 3d Sent from my iPad using Tapatalk
    Post by: tom1441, Aug 18, 2017 in forum: Projects
  4. tom1441
    Thread

    Robo 3D r1 plus

    I'm going to be replacing my arduino and ramps soon what steps do I need to do after replacing these parts. Is there anything I need to down load...
    Thread by: tom1441, Aug 18, 2017, 5 replies, in forum: Projects
  5. tom1441
    Post

    X carriage

    I did find a part on Thingiverse and finally got the order to go through
    Post by: tom1441, Mar 7, 2017 in forum: Troubleshooting
  6. tom1441
    Post

    X carriage

    Got the part ordered I hope
    Post by: tom1441, Mar 7, 2017 in forum: Troubleshooting
  7. tom1441
    Post

    X carriage

    No warranty
    Post by: tom1441, Mar 7, 2017 in forum: Troubleshooting
  8. tom1441
    Post

    X carriage

    Will post more tomorrow I want to thank everyone
    Post by: tom1441, Mar 7, 2017 in forum: Troubleshooting
  9. tom1441
    Post

    X carriage

    This is for a Robo 3D r1 plus machine Sent from my iPad using Tapatalk
    Post by: tom1441, Mar 7, 2017 in forum: Troubleshooting
  10. tom1441
    Thread

    X carriage

    I had a melt down. Where can I get a x carriage? All I need is the parts printed I have the bearings all I need are the plastic parts. Thanks for...
    Thread by: tom1441, Mar 7, 2017, 10 replies, in forum: Troubleshooting
  11. tom1441
    Post

    Answered Lack of parts and support with Robo

    R1plus the tech said switches and wiring harnesses
    Post by: tom1441, Dec 13, 2016 in forum: General Questions
  12. tom1441
    Post

    Answered Lack of parts and support with Robo

    It has been about three weeks and I haven't got my parts yet. They were under warranty even did a Skype with support.
    Post by: tom1441, Dec 13, 2016 in forum: General Questions
  13. tom1441
    Post

    Design molds to paint Crankbaits

    Yes but I would like to print the stencil on the robo,
    Post by: tom1441, Sep 20, 2016 in forum: Off Topic
  14. tom1441
    Post

    Design molds to paint Crankbaits

    http://www.lurecolourstudio.com/video-tutorials/gold-mica-bluegill.html
    Post by: tom1441, Sep 20, 2016 in forum: Off Topic
  15. tom1441
    Post

    Design molds to paint Crankbaits

    I've messed with 360 but I'm trying to make a stencil that will fit over a crankbait body to airbrush.
    Post by: tom1441, Sep 20, 2016 in forum: Off Topic
  16. tom1441
    Post

    Design molds to paint Crankbaits

    Ok thx
    Post by: tom1441, Aug 7, 2016 in forum: Off Topic
  17. tom1441
    Post

    Design molds to paint Crankbaits

    Thx
    Post by: tom1441, Aug 7, 2016 in forum: Off Topic
  18. tom1441
    Post

    Robo3D Replacements and Upgrades Thread

    Nice theard
    Post by: tom1441, Aug 6, 2016 in forum: Mods and Upgrades
  19. tom1441
    Post

    Design molds to paint Crankbaits

    Thanks Geof
    Post by: tom1441, Aug 6, 2016 in forum: Off Topic
  20. tom1441
    Post

    Design molds to paint Crankbaits

    http://www.lurecolourstudio.com/ if you could follow the tutorial how this guy paints Gold Mica Bluegill and you will what I'm trying to make.
    Post by: tom1441, Aug 6, 2016 in forum: Off Topic
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2