1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. STEM_Steve
    Post

    Heated bed for C2

    Any updates on this? I’d like to put a heated bed on my C2 as well. Thanks! Steve
    Post by: STEM_Steve, Jan 23, 2018 in forum: Mods and Upgrades
  2. STEM_Steve
    Post

    Cura for Mac install......

    Robo posted the profiles for the C2.. I have a R1 as well, but I don't use Cura for it.
    Post by: STEM_Steve, Mar 23, 2017 in forum: Software
  3. STEM_Steve
    Post

    Trying PETG

    Jeff, I noticed in your photo that on the two sides there is a "gap" between the edges. Was that by design or is that just the way it printed?...
    Post by: STEM_Steve, Mar 4, 2017 in forum: Filament
  4. STEM_Steve
    Post

    Cura on Windows....

    FYI.. check your material settings and make sure the PLA is the correct mm. Cura is having an issue (documented on their forum) where material...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Software
  5. STEM_Steve
    Post

    Cura for Mac install......

    There is a problem saving filament profile though.. https://github.com/Ultimaker/Cura/issues/1104 describes the issue. You have to create your...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Software
  6. STEM_Steve
    Post

    Print Adhesion

    10 minutes into the build and I can already tell you it's a totally different print experience. The layers are tight, print is smooth, and it's...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Show and Tell
  7. STEM_Steve
    Post

    Print Adhesion

    I looked at the slicer software and loaded the profiles per the instructions and I noticed that the PLA filament default that is loaded is 2.5mm...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Show and Tell
  8. STEM_Steve
    Post

    Auto bed leveling malfunction robo c2

    I'm having similar issues and at the point where I want to try something different for a bed. I'm not sold that a plastic bed isn't going to warp...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Troubleshooting
  9. STEM_Steve
    Post

    Print Adhesion

    To be honest, I haven't gotten anything to totally "stick" especially on the corners. I've tried hair spray, glue stick, and even tried using...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Show and Tell
  10. STEM_Steve
    Post

    Print Adhesion

    Do you find that the Z-Offset has to be re-done every couple of prints? Secondly, is your raft "sticking" to the build? I've yet to get a raft...
    Post by: STEM_Steve, Mar 3, 2017 in forum: Show and Tell
  11. STEM_Steve
    Thread

    Unanswered HotSpot default password?

    Anyone know what the HotSpot default password is, or know how to change it?
    Thread by: STEM_Steve, Feb 23, 2017, 0 replies, in forum: Troubleshooting
  12. STEM_Steve
    Post

    C2, Camera addition

    Here you go...
    Post by: STEM_Steve, Feb 23, 2017 in forum: Show and Tell
  13. STEM_Steve
    Post

    C2, Camera addition

    k, sorry... the .stl is a light cover (as specified)... Let me get the camera pieces and add it on here.
    Post by: STEM_Steve, Feb 23, 2017 in forum: Show and Tell
  14. STEM_Steve
    Post

    C2, Camera addition

    The login is the default:... from a mac terminal it would be ssh@[ipaddressofprinter], password is 'raspberry'
    Post by: STEM_Steve, Jan 7, 2017 in forum: Show and Tell
  15. STEM_Steve
    Post

    C2, Camera addition

    It was actually pretty straight forward. Setup a static IP for the Pi Enable the Webcam on the pi via SSH'ing into the Pi and then run sudo...
    Post by: STEM_Steve, Jan 7, 2017 in forum: Show and Tell
  16. STEM_Steve
    Post

    C2, Camera addition

    It's working from the application now.[ATTACH]
    Post by: STEM_Steve, Jan 7, 2017 in forum: Show and Tell
  17. STEM_Steve
    Post

    Anyone else get their C2 yet? some print samples showing up

    When calibrating the offset it says to use a piece of paper to gauge the gap between, what thickness of paper? I realize this may sound trivial,...
    Post by: STEM_Steve, Jan 7, 2017 in forum: General Questions
  18. STEM_Steve
    Post

    Anyone else get their C2 yet? some print samples showing up

    I'm having the same "stick" issue. I tried blue tape and it's not any better. Make sure you use the latest firmware if you try blue tape or else...
    Post by: STEM_Steve, Jan 7, 2017 in forum: General Questions
  19. STEM_Steve
    Post

    Solved My 2nd C2 arrived and just like the first it's broken :(

    Mine wasn't in very secure on 1 of the 3 printers I purchased an I didn't realize it until AFTER i started doing a test print. The force of the...
    Post by: STEM_Steve, Jan 7, 2017 in forum: Troubleshooting
  20. STEM_Steve
    Post

    C2, Camera addition

    If anyone is interested here is the file I used to make the light cover. I dropped the STL directly into OctoPrint and it took about 45 minutes on...
    Post by: STEM_Steve, Dec 25, 2016 in forum: Show and Tell
Showing results 1 to 20 of 22 Next >
Search Again
Page 1 of 2