1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. robodobo
    Post

    Solved Out-of-box Robo C2 microSD image

    With belated thanks to WheresWaldo and Tomlinson (in another related thread). I did as follows for a minimum of effort (not having to lift a...
    Post by: robodobo, Dec 5, 2017 in forum: Software
  2. robodobo
    Post

    LCD hung after Update

    Thanks for the help!!! Did they give any info about when they'll update their software so customers won't have to go through this (and loose...
    Post by: robodobo, Sep 19, 2017 in forum: Troubleshooting
  3. robodobo
    Post

    Solved uneven bed plate, is it fixable

    I used washers!! The print bed in my case was a whopping 0.9mm off -- over 12 cm -- raised in the front as well. That's about 0.4 degrees. I...
    Post by: robodobo, Jul 25, 2017 in forum: Troubleshooting
  4. robodobo
    Post

    PETG best filament without a heated bed?

    I use much lower temperatures for PETG on the R1, say 220C. The filament needs to cool down as fast as possible. That greatly improves corners...
    Post by: robodobo, May 4, 2017 in forum: Filament
  5. robodobo
    Post

    Solved Apply Robo customizations to new Cura?

    I could not install the Robo software for C2 on a PC either -- also it's unsigned and its relation to the Cura fork on Robo's website is dubious....
    Post by: robodobo, Apr 29, 2017 in forum: Software
  6. robodobo
    Post

    Partially Solved Issues Related to Problematic Extruder Design

    No surprise! I was about to look for my voodoo dolls. But with the capital infusion, grown-ups may help steer the company and get over this hump....
    Post by: robodobo, Apr 17, 2017 in forum: Troubleshooting
  7. robodobo
    Post

    Partially Solved Issues Related to Problematic Extruder Design

    Thanks, Mark, I edited: the official name is "filament release button" (from guide). Yes, it should be firm. Oh, I think it much worse than...
    Post by: robodobo, Apr 16, 2017 in forum: Troubleshooting
  8. robodobo
    Thread

    Partially Solved Issues Related to Problematic Extruder Design

    When I set up the C2, I followed the instructions in the beautifully designed Quick Start Guide. One step didn't seem right, that's when you're...
    Thread by: robodobo, Apr 16, 2017, 11 replies, in forum: Troubleshooting
  9. robodobo
    Post

    Troubleshooting C2: It's (perhaps) in the Owner's Manual !!!

    Thanks Mark, so it turns out that the C2 Manual with its troubleshooting section is maintained in Github -- some customer complaints apparently do...
    Post by: robodobo, Apr 10, 2017 in forum: Troubleshooting
  10. robodobo
    Thread

    Troubleshooting C2: It's (perhaps) in the Owner's Manual !!!

    The URL robo3d.com/manual resolves to support-site.readthedocs.io/en/latest/getting-started/index.html. There, the Robo 3D has put a very nice...
    Thread by: robodobo, Apr 10, 2017, 7 replies, in forum: Troubleshooting
  11. robodobo
    Post

    C2 Filament Run-Out Detection

    Thanks so much... Didn't even know C2 had a server onboard. The actual plugin name is Filament Sensor (2.2) on the second page under Plugin Manager.
    Post by: robodobo, Apr 7, 2017 in forum: Troubleshooting
  12. robodobo
    Post

    C2 Filament Run-Out Detection

    Same here --- finally got the Kickstarter campaign C2 printer. Can't print anything though --- for the same reason.
    Post by: robodobo, Apr 6, 2017 in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again