1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. jogul
    Post

    Solved USB cable from front panel

    Solved. Downloaded the imaged that is floating around. I thought my micros SD might be suspect and I didn't have another one so I used my...
    Post by: jogul, Sep 13, 2018 in forum: Troubleshooting
  2. jogul
    Post

    Solved USB cable from front panel

    I got the new LCD today and hooked it up. Still white screen. Could the SD card be corrupted. Where can a get the image so I can reflash it?
    Post by: jogul, Sep 12, 2018 in forum: Troubleshooting
  3. jogul
    Post

    Solved USB cable from front panel

    Printing OK tethered directly to computer. New LCD ordered from Amazon. Thanks for the link.
    Post by: jogul, Sep 10, 2018 in forum: Troubleshooting
  4. jogul
    Post

    Solved USB cable from front panel

    Can you tell me which one on Amazon? Also I just connected the USB output of the main board directly to my computer so I could check out...
    Post by: jogul, Sep 10, 2018 in forum: Troubleshooting
  5. jogul
    Post

    Solved USB cable from front panel

    Need to find an ethernet cable tomorrow morning and ty that.
    Post by: jogul, Sep 9, 2018 in forum: Troubleshooting
  6. jogul
    Post

    Solved USB cable from front panel

    When I scan my network for devices the Robo is not showing up. What does that mean?
    Post by: jogul, Sep 9, 2018 in forum: Troubleshooting
  7. jogul
    Post

    Solved USB cable from front panel

    Thanks. Now a second issue. The screen is white. Tried restarting several times. Still white, so I guess there is no way to operate the Bobo?
    Post by: jogul, Sep 9, 2018 in forum: Troubleshooting
  8. jogul
    Thread

    Solved USB cable from front panel

    I just bought a used C2 and the cable coming from the front USB port is not connected to anything inside. Where is it supposed to connect?
    Thread by: jogul, Sep 9, 2018, 20 replies, in forum: Troubleshooting
  9. jogul
    Post

    Pin out for Power Supply connector?

    Thanks for the information a spec sheet. That does look like a good power supply. The one I bought is much cheaper, but an unknown as far as...
    Post by: jogul, May 6, 2018 in forum: General Questions
  10. jogul
    Post

    Pin out for Power Supply connector?

    Thanks. I went for this combo. Seems to be working fine....
    Post by: jogul, May 6, 2018 in forum: General Questions
  11. jogul
    Post

    Pin out for Power Supply connector?

    Got it myself. Looking at the pins on the connector with the flat side up, the two left pins are + and the two right pins are -
    Post by: jogul, May 6, 2018 in forum: General Questions
  12. jogul
    Thread

    Pin out for Power Supply connector?

    For the R2 can someone tell me which pin is + and which pin is - ?
    Thread by: jogul, May 5, 2018, 5 replies, in forum: General Questions
  13. jogul
    Post

    ABS

    I'm going to remake the extruder cover in PETG. I don't have the Prusa orange but I have grey for now. That should work. It would be great if...
    Post by: jogul, Feb 10, 2018 in forum: Troubleshooting
  14. jogul
    Post

    ABS

    Yeah, coming to that conclusion. I have some parts that are close to high heat and since the ABS doesn't work I will go to PETG. That, so far,...
    Post by: jogul, Feb 10, 2018 in forum: Troubleshooting
  15. jogul
    Thread

    ABS

    I have tried everything I can think of including a cover for the front. I've increased the raft thickness, slowed down the print speed, used blue...
    Thread by: jogul, Feb 10, 2018, 10 replies, in forum: Troubleshooting
  16. jogul
    Thread

    Noise while idle.

    Is the noise I hear at idle, a mainboard fan? Is it supposed to be on at full speed when the printer is idle? Could it be throttled down? Is...
    Thread by: jogul, Feb 7, 2018, 17 replies, in forum: Troubleshooting
  17. jogul
    Post

    Simplify3d fff Profile?

    PLA. I was especially interested in the start and end codes which I would have to add.
    Post by: jogul, Feb 1, 2018 in forum: Software
  18. jogul
    Thread

    Simplify3d fff Profile?

    Does anyone have a Simplify 3d fff profile for the Robo c2?
    Thread by: jogul, Feb 1, 2018, 5 replies, in forum: Software
  19. jogul
    Post

    Solved Not Printing Right

    Printing has improved quite a bit by taking care of the slippage between the z rods and the couplers. What I did was take an aluminum pie pan and...
    Post by: jogul, Oct 17, 2016 in forum: Troubleshooting
  20. jogul
    Post

    Solved Not Printing Right

    I used tape on the threads and now the rod does not turn relative to the coupler. Hoping that will solve the problem. Will try it out shortly.
    Post by: jogul, Oct 15, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 40 Next >
Search Again
Page 1 of 2