1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. j93
    Thread

    First duel color print from bigbox

    I was going to retire the robo r1 but I just can't do it... I am think I am going to try the pallet + on the r1 but I do enjoy the e3d bigbox I...
    Thread by: j93, Feb 3, 2018, 1 replies, in forum: Show and Tell
  2. j93
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    I think i am going to pass the Robo on to my son when he leaves for college. I am running out of room in my office for toys. I still have an order...
    Post by: j93, Jan 23, 2018 in forum: Troubleshooting
  3. j93
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    I went back to the stock firmware and did not have the issue quite as bad, however the bed seemed to wobble and make a racket so i replaced the...
    Post by: j93, Jan 23, 2018 in forum: Troubleshooting
  4. j93
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    I adjusted the steps per mm during calibration. I'll lower the jerk settings some more and see if that helps.
    Post by: j93, Jan 14, 2018 in forum: Troubleshooting
  5. j93
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    I downloaded the firmware that danzca posted in the 1.1.7 firmware section on page 14. It was a prepackaged version for someone else but with the...
    Post by: j93, Jan 14, 2018 in forum: Troubleshooting
  6. j93
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    I am having the same exact issue with s3d after installing 1.1.7. matter control prints fine but s3d rattles so bad my layers are wonky.
    Post by: j93, Jan 13, 2018 in forum: Troubleshooting
  7. j93
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I did the upgrade to 1.1.7 today with the UBL. It did take forever for me to figure out how to get it all set up but it seems to have fixed my...
    Post by: j93, Jan 12, 2018 in forum: Mods and Upgrades
  8. j93
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I sure hope it corrects my issue. I replaced the bed ... The rods on the carriage etc trying to figure out the problem. I was watching from the...
    Post by: j93, Jan 5, 2018 in forum: Mods and Upgrades
  9. j93
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Awesome, I would settle for the 1.1.7 at this point just to get the leveling trough the LCD screen. My bed flexes so much during the leveling...
    Post by: j93, Jan 5, 2018 in forum: Mods and Upgrades
  10. j93
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    I have been having a battle for awhile with the Robo R1 Plus auto leveling. I would like to upgrade to the latest firmware with UBL. I have the...
    Post by: j93, Jan 5, 2018 in forum: Mods and Upgrades
  11. j93
    Thread

    Unanswered Parts not sized correctly after print.

    I ordered the smart LCD XXL from printed solid. I printed the case for it and it would not fit. I also issues with the parts fan not fitting into...
    Thread by: j93, Apr 15, 2016, 0 replies, in forum: Troubleshooting
  12. j93
    Post

    Simplify 3d

    I was looking to see if the Simplify3d software would auto level the r1+ like mattercontrol does?
    Post by: j93, Mar 26, 2016 in forum: Software
Showing results 1 to 12 of 12
Search Again