1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. TexasToon
    Post

    Robo3D Replacements and Upgrades Thread

    Does anyone have a source for a replacement 40mm cooling fan? Obviously I can plenty of 40mm 12v fans but I can't find one that has a 2pin...
    Post by: TexasToon, Apr 20, 2017 in forum: Mods and Upgrades
  2. TexasToon
    Post

    Cura 2.3.0 Settings

    So far so good ! thank you !!!!
    Post by: TexasToon, Mar 8, 2017 in forum: Software
  3. TexasToon
    Post

    Cura 2.3.0 Settings

    Thanks ! I'll try it and report back !!
    Post by: TexasToon, Mar 8, 2017 in forum: Software
  4. TexasToon
    Post

    Cura 2.3.0 Settings

    M104 S{print_temperature} ;set extruder temp M190 S{print_bed_temperature} ;preheat bed and wait G21 ;use metric values G90...
    Post by: TexasToon, Mar 8, 2017 in forum: Software
  5. TexasToon
    Post

    Cura 2.3.0 Settings

    Well, that was an epic fail, the temperatures reached set point before the print and then just started cooling..... Any suggestions?
    Post by: TexasToon, Mar 8, 2017 in forum: Software
  6. TexasToon
    Thread

    Cura 2.3.0 Settings

    Does anyone have any good settings for using Cura 2.3.0 ? Would gcode settings from previous revisions be compatible?
    Thread by: TexasToon, Mar 7, 2017, 12 replies, in forum: Software
  7. TexasToon
    Post

    How To: Cura 15.04 Setup

    2.3.0
    Post by: TexasToon, Mar 7, 2017 in forum: Software
  8. TexasToon
    Post

    How To: Cura 15.04 Setup

    I'm attempting to use Cura, my first print was a disaster, definite Z off set problems, so I've been trawling through this thread and looking at...
    Post by: TexasToon, Mar 7, 2017 in forum: Software
  9. TexasToon
    Post

    PLA Wood Filled Robo Filament - Print Settings?

    Glad I found this thread, I've had nothing but problems printing wood filament, I love the results but I've had a ton of jams and snapped...
    Post by: TexasToon, Mar 7, 2017 in forum: Printing Filament
  10. TexasToon
    Post

    Reducing Polygons in Matter Control

    I may have got round it, I just installed Cura, and I tried slicing the files in that and I didn't have a problem generating the gcodes, I'll see...
    Post by: TexasToon, Mar 6, 2017 in forum: Software
  11. TexasToon
    Thread

    Reducing Polygons in Matter Control

    I've encountered this problem a few times in Matter Control, where it warns me that I need to reduce the polygons before I can print, can I do...
    Thread by: TexasToon, Mar 6, 2017, 3 replies, in forum: Software
  12. TexasToon
    Post

    Solved Clogged extruder

    Ok I unblocked it, I heated up the hot-end and managed to force the filament through using a pick tool, wow it was stuck good ! Lets hope I can...
    Post by: TexasToon, Nov 28, 2016 in forum: Troubleshooting
  13. TexasToon
    Post

    Solved Clogged extruder

    Thats perfect thank you. I've now got the hot-end out but the filament is snapped off flush at the top of the cooling block, any advice on what I...
    Post by: TexasToon, Nov 28, 2016 in forum: Troubleshooting
  14. TexasToon
    Post

    Solved Clogged extruder

    I have the Robo3D R1 Plus and I'm noticing my extruder assembly is quite different from the one in thy youtube clip
    Post by: TexasToon, Nov 28, 2016 in forum: Troubleshooting
  15. TexasToon
    Post

    Solved Clogged extruder

    FYI its a 7mm wrench for the nozzle and an 18mm to hold the heater block, i've removed the nozzle but i can't see any material, I've even used an...
    Post by: TexasToon, Nov 27, 2016 in forum: Troubleshooting
  16. TexasToon
    Post

    Solved Clogged extruder

    Can can I unscrew the brass nozzle from the head without stripping down the whole assembly?
    Post by: TexasToon, Nov 27, 2016 in forum: Troubleshooting
  17. TexasToon
    Post

    Solved Clogged extruder

    i literally came here to post the same thing, is there a way to do this with minimal dismantling? I've taken out the two spring loaded screws and...
    Post by: TexasToon, Nov 26, 2016 in forum: Troubleshooting
  18. TexasToon
    Post

    Unresolved Prints slipping on PEI surface

    Call me a quitter but I took it off (wow did it put up a fight) I had yet another failed print due to lifting, its a nice idea but in practice...
    Post by: TexasToon, Nov 14, 2016 in forum: Troubleshooting
  19. TexasToon
    Post

    Unresolved Prints slipping on PEI surface

    I haven't done the sponge scrub thing yet, whats the thinking behind that? does it rough the surface to provide key for adherence? but yes I'm...
    Post by: TexasToon, Nov 11, 2016 in forum: Troubleshooting
  20. TexasToon
    Post

    Unresolved Prints slipping on PEI surface

    I always try my best to orientate my prints on the bed to minimize them but I presume there are times when they are unavoidable? so far as a total...
    Post by: TexasToon, Nov 11, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2