1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 4
  1. Jay312
    Post

    Any recommendations for 2D image to 3D model software

    No I just played with it a bit, like for a photo of a person it's not good. but a Black design it works for that
    Post by: Jay312, Mar 9, 2018 in forum: Software
  2. Jay312
    Thread

    Any recommendations for 2D image to 3D model software

    looking for software (easy to use) to make a normal 2d photo into a 3D model .stl file that I can print. Any recommendations?
    Thread by: Jay312, Mar 9, 2018, 2 replies, in forum: Software
  3. Jay312
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I uploaded it successfully now is there anything else to do to save it to the board? Do I have to type in a g code command?
    Post by: Jay312, Aug 22, 2017 in forum: Mods and Upgrades
  4. Jay312
    Post

    Community Favorite E3D v6 Information and Installation Guide

    So the ultimaker one is not commented out so just put the values there correct?
    Post by: Jay312, Aug 22, 2017 in forum: Mods and Upgrades
  5. Jay312
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I'm sorry I don't even know what commented out means lol. This is what I'm looking at
    Post by: Jay312, Aug 22, 2017 in forum: Mods and Upgrades
  6. Jay312
    Post

    Community Favorite E3D v6 Information and Installation Guide

    For the PID tuning do I just change the Values under Ultimaker?? It say this: If you are using a pre-configured hotend then you can use one of the...
    Post by: Jay312, Aug 21, 2017 in forum: Mods and Upgrades
  7. Jay312
    Post

    Partial Answer Possible short?

    how do I go about doing the test? Sorry if this is a stupid question lol.
    Post by: Jay312, Aug 17, 2017 in forum: Troubleshooting
  8. Jay312
    Post

    Partial Answer Possible short?

    yes fans went off too
    Post by: Jay312, Aug 17, 2017 in forum: Troubleshooting
  9. Jay312
    Post

    Partial Answer Possible short?

    Just a quick update I ordered a new thermistor and heater from robo and used those and still encountered the same issue, went into the firmware...
    Post by: Jay312, Aug 16, 2017 in forum: Troubleshooting
  10. Jay312
    Post

    How to Update and Edit Robo firmware with Arduino

    Getting this error message when I try to upload
    Post by: Jay312, Aug 16, 2017 in forum: Software
  11. Jay312
    Post

    Simplify 3d

    Thats the one I have Currently, I was just seeing if there was others. When I helped my buddy setup his gmax 1.5+ on the gmax site it actually had...
    Post by: Jay312, Aug 10, 2017 in forum: Software
  12. Jay312
    Post

    Partial Answer Possible short?

    I used the thermistor from the E3D V6 and the E3D v6 heater. I just cut the robo connections from the robo hot end and spliced them to the e3d v6...
    Post by: Jay312, Aug 10, 2017 in forum: Troubleshooting
  13. Jay312
    Post

    Partial Answer Possible short?

    Now will I have to redo or update the firmware after I replace the thermistor? I did read online once this problem happens they have trouble...
    Post by: Jay312, Aug 10, 2017 in forum: Troubleshooting
  14. Jay312
    Post

    Partial Answer Possible short?

    Think I found the problem
    Post by: Jay312, Aug 10, 2017 in forum: Troubleshooting
  15. Jay312
    Post

    Partial Answer Possible short?

    tried a print in matter control and I'm getting a hardware error, sorry for all the posts, I'm just trying to be as exact as possible to try and...
    Post by: Jay312, Aug 10, 2017 in forum: Troubleshooting
  16. Jay312
    Post

    Partial Answer Possible short?

    Also did not do any firmware updates for the E3D V6 or the xxl lcd
    Post by: Jay312, Aug 9, 2017 in forum: Troubleshooting
  17. Jay312
    Post

    Partial Answer Possible short?

    S3D error photo
    Post by: Jay312, Aug 9, 2017 in forum: Troubleshooting
  18. Jay312
    Thread

    Partial Answer Possible short?

    So I finished my E3D V6 and XXL LCD controller, on my R1 Plus. Printer has been printing great for about a week. Now two issues are happening A)...
    Thread by: Jay312, Aug 9, 2017, 18 replies, in forum: Troubleshooting
  19. Jay312
    Post

    Simplify 3d

    Is there a way to put the Robo R1+ Printer photo in S3D Instead of just having the build plate area? Not that it's really needed lol I just seem...
    Post by: Jay312, Aug 8, 2017 in forum: Software
  20. Jay312
    Post

    Solved Print Bed "Upgrade"

    Which Micro center has them?
    Post by: Jay312, Aug 2, 2017 in forum: General Questions
Showing results 1 to 20 of 64 Next >
Search Again
Page 1 of 4