1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Caleb Cangelosi
    Post

    Has anyone ever used trnio 3D scanning software?

    Thanks, Geof. I'll give him a call.
    Post by: Caleb Cangelosi, Aug 15, 2017 in forum: Projects
  2. Caleb Cangelosi
    Post

    Has anyone ever used trnio 3D scanning software?

    Thanks for the warnings! This is actually going to be more of a charity scan, not a job. But from what you say, it may turn into a job, or...
    Post by: Caleb Cangelosi, Aug 15, 2017 in forum: Projects
  3. Caleb Cangelosi
    Thread

    Has anyone ever used trnio 3D scanning software?

    I have an opportunity to do some 3D scanning for an individual this week, but I don't own a 3D scanner and so I've been looking around at...
    Thread by: Caleb Cangelosi, Aug 14, 2017, 11 replies, in forum: Projects
  4. Caleb Cangelosi
    Post

    Solved Raft first layer vs non-raft first layer

    Thanks, Mark. Do you have any idea what the slicer adjusts it to when it does a raft? It seems a lot bigger than without a raft. I guess I should...
    Post by: Caleb Cangelosi, Feb 3, 2017 in forum: Troubleshooting
  5. Caleb Cangelosi
    Thread

    Solved Raft first layer vs non-raft first layer

    I am frustrated by the fact that I have to print with a raft most times, even on prints that have a flat bottom, like a box. When I do a raft, the...
    Thread by: Caleb Cangelosi, Feb 3, 2017, 4 replies, in forum: Troubleshooting
  6. Caleb Cangelosi
    Post

    Solved Bed not aligned with Matter Control or S3D

    I'll just tweak it manually. I print with PETG, and it tends to lift when it isn't on the heated part (or perhaps it's because I haven't applied...
    Post by: Caleb Cangelosi, Jan 27, 2017 in forum: Troubleshooting
  7. Caleb Cangelosi
    Post

    Solved Bed not aligned with Matter Control or S3D

    Bummer - so how do you think it happened to get off?
    Post by: Caleb Cangelosi, Jan 27, 2017 in forum: Troubleshooting
  8. Caleb Cangelosi
    Thread

    Solved Bed not aligned with Matter Control or S3D

    The digital print bed in both Matter Control and Simplify 3D is about an inch off (front to back). So for example, a piece that shows up as...
    Thread by: Caleb Cangelosi, Jan 27, 2017, 6 replies, in forum: Troubleshooting
  9. Caleb Cangelosi
    Post

    Solved Moving the Extruder with Simplify3d

    Thanks Mark! I've looked at a lot of videos, but hadn't seen this one yet. I'm really excited about being able to do multiple processes on...
    Post by: Caleb Cangelosi, Jan 14, 2017 in forum: Troubleshooting
  10. Caleb Cangelosi
    Thread

    Solved Moving the Extruder with Simplify3d

    I finally bit the bullet and bought Simplify3D. I'm already enjoying what I can do with it. But I haven't been able to figure out how to do...
    Thread by: Caleb Cangelosi, Jan 14, 2017, 5 replies, in forum: Troubleshooting
  11. Caleb Cangelosi
    Post

    E3d v6

    I just changed from a hex to an E3D v6, and I did have to change the firmware because I used the canister thermistor from E3D. II believe if you...
    Post by: Caleb Cangelosi, Dec 23, 2016 in forum: General Questions
  12. Caleb Cangelosi
    Post

    E3D v6 Information, Installation Guides, and Review

    This was incredibly helpful for a newbie to Arduino like me. Thank you!!
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Mods and Upgrades
  13. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    Oh, ok. Man, if I would have known how much electronics I'd need to enjoy this hobby I may never have gotten started. But I'm glad I did and I'm...
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  14. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    Thanks Geof. I may have made the same mistake on my thermistor. Sent from my iPhone using Tapatalk
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  15. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    Thanks Mark. So that means my parts fan is connected where it needs to be. When I get home I'll have to check whether I indeed installed the hot...
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  16. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    So Geof, are you saying that I should have my parts fan in F0? Thanks! Sent from my iPhone using Tapatalk
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  17. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    I just realized that I have my parts fan plugged into Fan0, and my hot end fan is plugged into Fan2+ next to the LED plugs and the RAMPS board...
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  18. Caleb Cangelosi
    Post

    Unanswered Where do I plug in my E3D v6 hot end fan?

    I'm pretty sure I do have it plugged in there. But when I turned the printer on the fan didn't spin. And the E3D assembly wiki says this: "Fan...
    Post by: Caleb Cangelosi, Dec 21, 2016 in forum: Troubleshooting
  19. Caleb Cangelosi
    Thread

    Unanswered Where do I plug in my E3D v6 hot end fan?

    I've gotten my E3D extruder assembled and installed, but I don't think I have the hot end fan in the right place. When I turned on the power the...
    Thread by: Caleb Cangelosi, Dec 20, 2016, 14 replies, in forum: Troubleshooting
  20. Caleb Cangelosi
    Post

    Solved Cleaning the print bed

    Sorry - auto correct fail - I meant Windex, like the other guys wrote. :-)
    Post by: Caleb Cangelosi, Dec 14, 2016 in forum: General Questions
Showing results 1 to 20 of 47 Next >
Search Again
Page 1 of 3