1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Jutte
    Thread

    Belt tension

    The tension on the belt on the left side of my R2 is much looser than the one on the right. Prints seem to be OK so far. Does this belt need to be...
    Thread by: Jutte, Sep 23, 2018, 2 replies, in forum: Troubleshooting
  2. Jutte
    Thread

    Where is this from?

    Better and better. What do you suppose this fell out of?
    Thread by: Jutte, Jul 15, 2018, 4 replies, in forum: Troubleshooting
  3. Jutte
    Thread

    Can't reset target temp

    After printing with ABS I am now unable to reset the target temp. I have tried doing so manually but it doesn't take. When printing with PLA the...
    Thread by: Jutte, Jun 30, 2018, 5 replies, in forum: Troubleshooting
  4. Jutte
    Thread

    Extrusion problem

    I'm having a problem with filament not extruding when printing. I just installed the ruby nozzle and completed a print with it with no problems...
    Thread by: Jutte, Jun 21, 2018, 8 replies, in forum: Troubleshooting
  5. Jutte
    Thread

    Algix filament

    I just got a Micromark catalog today which had a page of several varieties of Algix filament. Has anyone used this brand of filament? If so, how...
    Thread by: Jutte, Jan 30, 2017, 0 replies, in forum: Printing Filament
  6. Jutte
    Thread

    Lightbulb for 3D Prints

    Has anyone used one of these Toolmon bulbs? It looks like a good ready-made insert for items intended to be lit up inside, but a bit pricey....
    Thread by: Jutte, Jun 19, 2016, 2 replies, in forum: General Questions
  7. Jutte
    Thread

    Printing on Fabric

    Has anyone tried printing on fabric on a Robo? I may try this over the weekend....
    Thread by: Jutte, May 26, 2016, 13 replies, in forum: Projects
  8. Jutte
    Thread

    Metal filaments

    I am eager to try metal filaments like copper and bronze. Anybody had experience printing with it? What brands do you like best? Does the print...
    Thread by: Jutte, May 6, 2016, 4 replies, in forum: Printing Filament
  9. Jutte
    Thread

    PLA Wood Filament

    Not sure just what I expected, but I'm not terribly impressed with the wood filament. It's brown but beyond that it just looks like PLA. What...
    Thread by: Jutte, Apr 23, 2016, 17 replies, in forum: Printing Filament
  10. Jutte
    Thread

    Smooth Operator

    One week in on my refurbished Robo R1, I am impressed with the relatively low noise level compared to my Cube 3. While the Cube 3 sounds like a...
    Thread by: Jutte, Apr 19, 2016, 0 replies, in forum: General Questions
  11. Jutte
    Thread

    Solved Disconnected cable

    I just discovered a cable that was sitting at the left side unconnected to anything. I have been printing and had no issues other than filament...
    Thread by: Jutte, Apr 12, 2016, 4 replies, in forum: Troubleshooting
  12. Jutte
    Thread

    Hello from central Florida

    I'm a relative novice to 3d printing. My first printer was a Cube 3 which I still love, but it has limitations and has been discontinued. I...
    Thread by: Jutte, Apr 12, 2016, 4 replies, in forum: United States of America
Showing results 1 to 12 of 12
Search Again