1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 3
  1. Doug Meek
    Thread

    New filament out detector with movement sensing for jams

    I've designed a new filament out sensor for the Robo. This is a little different from most filament out sensors out there as this one will detect...
    Thread by: Doug Meek, Jun 10, 2017, 4 replies, in forum: Mods and Upgrades
  2. Doug Meek
    Post

    Solved Build Plate Issues (No heat)

    Incase you or anyone else needs connectors in the future....the parts for the connectors are: [IMG] A98223-ND 796634-2 A98223-ND 796634-2 TERM...
    Post by: Doug Meek, May 10, 2017 in forum: Troubleshooting
  3. Doug Meek
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    You may want to move your mounting plate to the inside (toward the back) of the bracket to get the IR sensor closer to the extruder, just makes...
    Post by: Doug Meek, May 4, 2017 in forum: Mods and Upgrades
  4. Doug Meek
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Good to know! I may just wait till you get them posted since you are so close. Thanks for the heads up Something I have been fighting for any of...
    Post by: Doug Meek, Apr 28, 2017 in forum: Mods and Upgrades
  5. Doug Meek
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    No, I have the filament out sensor and it was a suggestion for debugging it so it was just in my list of previous changes so I included it....
    Post by: Doug Meek, Apr 28, 2017 in forum: Mods and Upgrades
  6. Doug Meek
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Was contemplating going to the bugFix R1+ MESH version but after enabling #define PINS_DEBUGGING the compiler spits out dozens of conversion...
    Post by: Doug Meek, Apr 28, 2017 in forum: Mods and Upgrades
  7. Doug Meek
    Post

    Answered Build Plate connectors burnt up, almost started a fire

    I just had the exact same thing happen, connector looked identical to yours. Ordered new connectors from Digikey, replaced the 2 pin plug and the...
    Post by: Doug Meek, Apr 26, 2017 in forum: Troubleshooting
  8. Doug Meek
    Post

    Answered S3D auto level issues

    Is there anything entered under 'Global G-Code Offsets' on the G-Code tab in the Process you are using? I think S3D adds whatever value is listed...
    Post by: Doug Meek, Apr 23, 2017 in forum: Troubleshooting
  9. Doug Meek
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    That's what I was thinking since this was coming from SanityCheck.h.... So someone should correct the Ops first entry so as not to confuse anyone...
    Post by: Doug Meek, Apr 22, 2017 in forum: Mods and Upgrades
  10. Doug Meek
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    1.1 RC8 using Arduino 1.8.1
    Post by: Doug Meek, Apr 22, 2017 in forum: Mods and Upgrades
  11. Doug Meek
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Why when I enable PIDTEMPBED and BED_LIMIT_SWITCHING do I get a compile error of "To use BED_LIMIT_SWITCHING you must disable PIDTEMPBED"?...
    Post by: Doug Meek, Apr 22, 2017 in forum: Mods and Upgrades
  12. Doug Meek
    Post

    Solved Printing goes off axis mid print

    I had to cover mine, with the aluminum tape, within the first couple of months of owning mine! On mine I had a piece of the original tape get...
    Post by: Doug Meek, Apr 10, 2017 in forum: Troubleshooting
  13. Doug Meek
    Post

    Solved Thermal Runaway on Bed heater

    Well I found the problem, the connector for the bed heater to the RAMPS where the set screws hold the wires were slightly loose so when it started...
    Post by: Doug Meek, Apr 10, 2017 in forum: Troubleshooting
  14. Doug Meek
    Post

    Solved Thermal Runaway on Bed heater

    Thanks for the temporary fix...I did disable the warnings and that allowed the prints to finish and monitoring the bed temps during the prints I...
    Post by: Doug Meek, Apr 9, 2017 in forum: Troubleshooting
  15. Doug Meek
    Thread

    Solved Thermal Runaway on Bed heater

    Just yesterday my printer started giving me this error every time I attempt a print. It will go for awhile (5-10 layers) and then pop up ending...
    Thread by: Doug Meek, Apr 9, 2017, 4 replies, in forum: Troubleshooting
  16. Doug Meek
    Post

    Filament Runout Sensor (FRS) upgrade to Robo R1/R1+

    Are you meaning the M43 P20 command form this? Debugging and testing is fairly easy when you enable PINS_DEBUGGING in the firmware explained above...
    Post by: Doug Meek, Apr 8, 2017 in forum: Mods and Upgrades
  17. Doug Meek
    Post

    Solved Getting prints to stick

    PEI works really well also, that's all I use but as in any solution your offset needs to be right.
    Post by: Doug Meek, Feb 9, 2017 in forum: Troubleshooting
  18. Doug Meek
    Post

    Anyone install a BLtouch on their robo?

    I went with the mini IR probe from here...
    Post by: Doug Meek, Jan 7, 2017 in forum: Mods and Upgrades
  19. Doug Meek
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    jim3Dbot - Thanks for the info, I'll see what I can do tonight and send it to you if I get nowhere. danzca6 - I had it mounted in my fan shroud,...
    Post by: Doug Meek, Jan 5, 2017 in forum: Mods and Upgrades
  20. Doug Meek
    Post

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Well I love this mini IR but I had a problem with a runaway print last night and before I got to it it had moved a few things around. One of the...
    Post by: Doug Meek, Jan 4, 2017 in forum: Mods and Upgrades
Showing results 21 to 40 of 54 Next >
Search Again
Page 2 of 3