1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    You are right, I changed my fans that blow to the extruder with the slower one and run at 100%. Now I print without any warning (cross fingers :))...
    Post by: deeph, Aug 21, 2016 in forum: Mods and Upgrades
  2. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Just 2 fans blowing from front and rear, I will take a picture later. I'm printing 0.1mm at 1600mm/min, is this too slow or too fast?
    Post by: deeph, Aug 21, 2016 in forum: Mods and Upgrades
  3. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Still not work properly, but now noticed if I detach 1 hotend cooling fan (I run 2 cooling fans for hotend) then I raise the extruder temp it...
    Post by: deeph, Aug 21, 2016 in forum: Mods and Upgrades
  4. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yup I'm using fan for cooling. It seems, first layer still provided target temp but 2nd layer and above the temp descending for a while and up...
    Post by: deeph, Aug 20, 2016 in forum: Mods and Upgrades
  5. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I have problem with temperature when printing with 0.1mm layer height. The actual temp was lower than target temp when printing 2nd layer and...
    Post by: deeph, Aug 20, 2016 in forum: Mods and Upgrades
  6. deeph
    Post

    reprapdiscount LCD display

    More thing that I noticed with the LCD is the file name when start printing pop up too fast so not sure which file I print is the correct one. Can...
    Post by: deeph, Aug 15, 2016 in forum: Mods and Upgrades
  7. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Thanks, I will try to upload it.
    Post by: deeph, Aug 13, 2016 in forum: Mods and Upgrades
  8. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I saw old firmware and does the z step is 2267.72 for inch lead screw? For a while I'm still using my stock lead screw. I will make a upgrade in...
    Post by: deeph, Aug 13, 2016 in forum: Mods and Upgrades
  9. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Yes mine is R1 but the old one, forgot to mentioned before. Ohh and I haven't upgraded the lead screw. Ok, I will change the Z step with the...
    Post by: deeph, Aug 13, 2016 in forum: Mods and Upgrades
  10. deeph
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Does this version of the firmware work with Old Robo3D with 5/16 threaded rod? BTW, how do I know if my lead screw on inch or mm? Just to make...
    Post by: deeph, Aug 13, 2016 in forum: Mods and Upgrades
  11. deeph
    Post

    reprapdiscount LCD display

    I have problem with LCD display's offset. I set my offset in S3D at 0.7. Does the offset in LCD display will override the S3D's offset or vise...
    Post by: deeph, Aug 12, 2016 in forum: Mods and Upgrades
  12. deeph
    Thread

    Printing problem

    I have problem printing with PLA. There is aspot that the prints not good. Picture: [IMG] That problem only came out in the middle of an angle....
    Thread by: deeph, Nov 18, 2014, 13 replies, in forum: Troubleshooting
  13. deeph
    Thread

    Layer above the support material

    Hi, I have printed some models the result is great but if there is a 'support material'. The layer (above the support material) of the part is...
    Thread by: deeph, Oct 12, 2014, 12 replies, in forum: Troubleshooting
Showing results 1 to 13 of 13
Search Again