1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. JohnShuba
    Post

    Detect Wire vs. Wireless, change your hostname, and add a Static IP

    One thing that is important to mention is that when connecting the Robo C2 Printer to Cura 2.3.1 on windows it has difficulties detecting the...
    Post by: JohnShuba, Mar 26, 2017 in forum: Software
  2. JohnShuba
    Post

    Detect Wire vs. Wireless, change your hostname, and add a Static IP

    Thanks for the information that is good not know, I guess I will stay away from 10.x subnet. I just checked my network status on the C2 after your...
    Post by: JohnShuba, Mar 26, 2017 in forum: Software
  3. JohnShuba
    Thread

    Detect Wire vs. Wireless, change your hostname, and add a Static IP

    I recently needed to change to a static IP address to install a camera on the Robo C2. I am new to the Raspberry OS so I am posting this to help...
    Thread by: JohnShuba, Mar 26, 2017, 5 replies, in forum: Software
  4. JohnShuba
    Thread

    Robo C2 Image download link.

    As many of you know, there is no link for a download of a startup Raspberry Pi image for the Robo C2. If you call Robo support, they are nice...
    Thread by: JohnShuba, Mar 19, 2017, 61 replies, in forum: Software
  5. JohnShuba
    Post

    Original Image of the C2 load? What The Hell!

    Thanks @mark tomlinson for the image backup. I will make a new post to share with the other users once I upgrade it to the newest releases and...
    Post by: JohnShuba, Mar 18, 2017 in forum: Troubleshooting
  6. JohnShuba
    Post

    Original Image of the C2 load? What The Hell!

    Thank you so much I will message you and take you up on your offer.
    Post by: JohnShuba, Mar 18, 2017 in forum: Troubleshooting
  7. JohnShuba
    Post

    Original Image of the C2 load? What The Hell!

    Yes @colton81 you are right version 1.1.4-C2.3 is installed on mine and runs very stable.
    Post by: JohnShuba, Mar 18, 2017 in forum: Troubleshooting
  8. JohnShuba
    Post

    Original Image of the C2 load? What The Hell!

    Oh, just as a side note if your SD image goes bad than of course you need a download of the original image to restore the system. After all, if...
    Post by: JohnShuba, Mar 17, 2017 in forum: Troubleshooting
  9. JohnShuba
    Thread

    Original Image of the C2 load? What The Hell!

    I have been doing some upgrades to the Robo C2. Even though I made a backup after a few changes to the original image from the SD card, I would...
    Thread by: JohnShuba, Mar 17, 2017, 11 replies, in forum: Troubleshooting
  10. JohnShuba
    Thread

    Upgraded display to 7" capacative touchscreen

    I upgraded to a touchscreen that work a bit better that the one that comes with the Robo C2. I added a 7 inch 800 x 480 capacative touchscreen....
    Thread by: JohnShuba, Mar 16, 2017, 13 replies, in forum: Mods and Upgrades
  11. JohnShuba
    Post

    Print Curling

    Mine at first had the same curling issue. Once I got use to the Z-offset "setting it correctly it takes practice" and then I raised the tempature...
    Post by: JohnShuba, Mar 10, 2017 in forum: Troubleshooting
  12. JohnShuba
    Post

    Filament Sale until 03/11/17

    You can orderit online with that prome code
    Post by: JohnShuba, Mar 10, 2017 in forum: Off Topic
  13. JohnShuba
    Thread

    Run out of bed tape what do you do?

    I have projects I want to do this weekend and I ran out of bed tape. I order some but the sheets will not get here till mid to late next week. So...
    Thread by: JohnShuba, Mar 10, 2017, 0 replies, in forum: Printing Filament
  14. JohnShuba
    Thread

    Filament Sale until 03/11/17

    www.frys.com has 10 dollars off Shaxon filament till tommorow 03/11/17. You need to enter this Promo Code: 9065725. I picked up twp PLA spools...
    Thread by: JohnShuba, Mar 10, 2017, 3 replies, in forum: Off Topic
  15. JohnShuba
    Post

    First Project with Robo-C2 - 1911 Grips

    PLA
    Post by: JohnShuba, Mar 10, 2017 in forum: Show and Tell
  16. JohnShuba
    Post

    Cura tempature material problem

    Thank you everyone that is good info :), and yes some of the commands are layers deep in the menu structure. I just got to dig deeper i guess.
    Post by: JohnShuba, Mar 10, 2017 in forum: General Questions
  17. JohnShuba
    Post

    First Project with Robo-C2 - 1911 Grips

    I changed my mind, I would hate to have you recreate them. These grips fit a compact 1911 RIA, with a magazine guide/weld installed, they could...
    Post by: JohnShuba, Mar 10, 2017 in forum: Show and Tell
  18. JohnShuba
    Post

    Cura tempature material problem

    [ATTACH] I found you can set tempature in Cura under custom but still can not set it base on material selection. Here is my gcode start...
    Post by: JohnShuba, Mar 10, 2017 in forum: General Questions
  19. JohnShuba
    Thread

    Cura tempature material problem

    I notice in the Cura software when it writes the gcode file it does not set the material tempature to the material selected in the library. Its...
    Thread by: JohnShuba, Mar 10, 2017, 20 replies, in forum: General Questions
  20. JohnShuba
    Post

    First Project with Robo-C2 - 1911 Grips

    Thanks for your interest in these gip but at this time Im keeping them in my vault.
    Post by: JohnShuba, Mar 10, 2017 in forum: Show and Tell
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2