1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 3
  1. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Seemed to print too fast. The top layer seemed to fall into the hole rather than form a raft for the final laters. maybe too hot and too fast?...
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  2. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    This time I left the settings the same and tried glue stick as I had one. I don't have hair, hence to hairspray! :) It's on about layer 30 out of...
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  3. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Went to print the "whistle" and it started to lift. What is the most common reason for lift? For PLA on my E3D, I have it running 210C and 50C on...
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  4. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Printed! Would the top be because of the low quality setting? Layers set to .3mm and fill density to .2%.
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  5. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    It printed! No glue or hairspray or anything. Only one small area where it lifted on an end of an outer calibration quarter. Going to try to print...
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  6. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    how do I make sure it avoids the binder clips?
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  7. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Well, I did a calibration circle w/o the glass or calibration, and it printed out! Obviously it was just sorta circles and squiggles, but it...
    Post by: SPyKER, Apr 8, 2017 in forum: Mods and Upgrades
  8. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    So I added conically-tapered compression springs to the corners because that is all I have had time for, but wonder if I don't have things turned...
    Post by: SPyKER, Apr 7, 2017 in forum: Mods and Upgrades
  9. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    So last night I ran into a new problem with the y-axis. All of a sudden, the y-axis seems to be getting "stuck" and won't move correctly without a...
    Post by: SPyKER, Apr 7, 2017 in forum: Mods and Upgrades
  10. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I think I might give 3DPrinterOS a whirl. They have a Robo 3D R1 setting already.
    Post by: SPyKER, Apr 6, 2017 in forum: Mods and Upgrades
  11. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Best free program?
    Post by: SPyKER, Apr 6, 2017 in forum: Mods and Upgrades
  12. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    So, looking at some other posts, I closed Matter Control, and restarted it. Working fine now (without filament) except I can see that my glass on...
    Post by: SPyKER, Apr 6, 2017 in forum: Mods and Upgrades
  13. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Seems All home but the buttons for movement won't move the motors
    Post by: SPyKER, Apr 5, 2017 in forum: Mods and Upgrades
  14. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    So, in matter control, I can home everything, but when I choose print (calibration circle loaded) it thinks it's printing but nothing moves?
    Post by: SPyKER, Apr 5, 2017 in forum: Mods and Upgrades
  15. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    I loosened the screw holding the thermistor in and it dropped to 25C, so it appears to be working now
    Post by: SPyKER, Apr 5, 2017 in forum: Mods and Upgrades
  16. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    So, the motors are working well, and I about have home calibrated. My new problem is that the thermistors are reading around 350C for the hotend...
    Post by: SPyKER, Apr 5, 2017 in forum: Mods and Upgrades
  17. SPyKER
    Thread

    Amazon has Monoprice Crystal Clear Filament $11.52 today with Prime

    http://a.co/dCuWEs7
    Thread by: SPyKER, Apr 5, 2017, 1 replies, in forum: Off Topic
  18. SPyKER
    Post

    Solved Sites like thingiverse?

    https://all3dp.com/best-sites-free-stl-files-3d-printing/
    Post by: SPyKER, Apr 5, 2017 in forum: General Questions
  19. SPyKER
    Post

    Kickstarter Edition: Full rebuild help

    Tonight I was able to get the lower GT2 belt changed and tightened with the bed back on (didn't replace the plastic with springs because I want to...
    Post by: SPyKER, Apr 4, 2017 in forum: Mods and Upgrades
  20. SPyKER
    Post

    Time for Aluminum bed.

    Thank you guys for figuring this out for us. As soon as I upgrade to the linear rods instead of slides, this is will be on the agenda. I'll likely...
    Post by: SPyKER, Apr 4, 2017 in forum: Mods and Upgrades
Showing results 21 to 40 of 55 Next >
Search Again
Page 2 of 3