1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 8
  1. Avrution
    Post

    Solved Unprinted section on prints?

    I think it might be something else. Tried it again in ABS and the same exact spot. Oiler is still probably a good idea. Need to try another...
    Post by: Avrution, Jan 30, 2019 in forum: Troubleshooting
  2. Avrution
    Post

    Solved Unprinted section on prints?

    It is PLA. I've printed 2/3 of this roll already without an issue. Edit - pulling out another roll I noticed it covered in dust. I keep a few...
    Post by: Avrution, Jan 30, 2019 in forum: Troubleshooting
  3. Avrution
    Post

    Solved Unprinted section on prints?

    Still running when turned on
    Post by: Avrution, Jan 29, 2019 in forum: Troubleshooting
  4. Avrution
    Post

    Solved Unprinted section on prints?

    Fan on the bottom of the base?
    Post by: Avrution, Jan 29, 2019 in forum: Troubleshooting
  5. Avrution
    Thread

    Solved Unprinted section on prints?

    Not sure what the correct term is for this, but if you look at the picture you will see a chunk of print is essentially missing all around every...
    Thread by: Avrution, Jan 29, 2019, 41 replies, in forum: Troubleshooting
  6. Avrution
    Post

    Unanswered Anyone tried Octolapse with the R1/R1+?

    Thanks for the input, I was kind of afraid of how it might affect prints with the extra movements and pauses it introduces. I do normally print...
    Post by: Avrution, Jul 11, 2018 in forum: General Questions
  7. Avrution
    Post

    Unanswered Anyone tried Octolapse with the R1/R1+?

    Would love to, but recently had surgery and printer is upstairs - just recently using stairs after a month and trial and error time will have to...
    Post by: Avrution, Jul 8, 2018 in forum: General Questions
  8. Avrution
    Thread

    Unanswered Anyone tried Octolapse with the R1/R1+?

    I've had this installed since it was released, but have yet to try. Anyone have experience with it and if so, what settings did you end up...
    Thread by: Avrution, Jul 7, 2018, 4 replies, in forum: General Questions
  9. Avrution
    Thread

    Solved New extruder fan, prints not bonding now - coincidence?

    Printing for the first time in two weeks - nothing has changed aside from having my extruder fan replaced. I am able to "print", but it seems...
    Thread by: Avrution, Mar 2, 2018, 0 replies, in forum: Troubleshooting
  10. Avrution
    Post

    Simplify 3d

    I've been pretty happy with my prints, but I haven't touched any options outside of the basics. I'm trying to work on my bridging performance and...
    Post by: Avrution, Mar 2, 2018 in forum: Software
  11. Avrution
    Post

    Simplify 3d

    I noticed you went back to the defaults on the extrusion multiplier and width. Do you actually tune your flowrate for S3D or just stick with the .90?
    Post by: Avrution, Mar 2, 2018 in forum: Software
  12. Avrution
    Post

    Simplify 3d

    So, it turns out what makes the difference in the preview is the Advanced option "Only retract when crossing open spaces" - on yours it was...
    Post by: Avrution, Mar 2, 2018 in forum: Software
  13. Avrution
    Post

    Simplify 3d

    With that same profile on 4.0.1? It is so odd.
    Post by: Avrution, Mar 2, 2018 in forum: Software
  14. Avrution
    Post

    Simplify 3d

    Finally had a change to print the cube and it did indeed print how it looked. Ugliest calibration cube I've ever made ;) Some models seem to...
    Post by: Avrution, Mar 2, 2018 in forum: Software
  15. Avrution
    Post

    Thinking about Precision Piezo

    How has repeatability been? I know whenever I tried to use UBL the numbers would wildly change every single time even if doing it consecutively.
    Post by: Avrution, Feb 26, 2018 in forum: Mods and Upgrades
  16. Avrution
    Post

    Thinking about Precision Piezo

    How have your numbers been comparing the probing with and without? Looks like it isn't even making contact with the bed so is it that precise?
    Post by: Avrution, Feb 26, 2018 in forum: Mods and Upgrades
  17. Avrution
    Post

    Simplify 3d

    I'm really curious to see if I'd get a funky cube
    Post by: Avrution, Feb 24, 2018 in forum: Software
  18. Avrution
    Post

    Simplify 3d

    Simplify 3d
    Post by: Avrution, Feb 24, 2018 in forum: Software
  19. Avrution
    Post

    Simplify 3d

    Won't know till next week. Just found it really odd how it previews, especially compared to my regular profile.
    Post by: Avrution, Feb 24, 2018 in forum: Software
  20. Avrution
    Post

    Simplify 3d

    Been out of town so unable to test, but just looking at the preview of a cube is really odd compared to normal (This is Geofs profile settings)....
    Post by: Avrution, Feb 24, 2018 in forum: Software
Showing results 21 to 40 of 142 Next >
Search Again
Page 2 of 8