1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 6
  1. Gary Boyce
    Post

    Solved poor Printing Quality

    Still looks way too close. When using buildtak, you don't need it so close that its translucent. Also, I would continue testing with a smaller...
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  2. Gary Boyce
    Post

    Solved poor Printing Quality

    You just need to change what settings are visible. Go to Settings in the top menu and select Configure Setting Visability.[IMG][IMG] Sent from...
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  3. Gary Boyce
    Post

    Solved poor Printing Quality

    Under the Quality settings. Initial Layer Height. [IMG] Sent from my SM-G930V using Tapatalk
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  4. Gary Boyce
    Post

    Solved poor Printing Quality

    You do this in your slicer settings. What slicer do you use? Sent from my SM-G930V using Tapatalk
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  5. Gary Boyce
    Post

    Solved poor Printing Quality

    I had the same issue with my R2. I ran it with the nozzle that close for a year before I began having trouble. Mine was set for .2 first layer...
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  6. Gary Boyce
    Post

    Solved poor Printing Quality

    It looks like your first layer is way too close. What is your first layer height set to? Sent from my SM-G930V using Tapatalk
    Post by: Gary Boyce, Jan 19, 2019 in forum: Troubleshooting
  7. Gary Boyce
    Post

    Marlin for the R2 - UBL Enabled

    The problem was that I defined the board as // The following define selects which electronics board you have. // Please choose the name from...
    Post by: Gary Boyce, Jan 13, 2019 in forum: Mods and Upgrades
  8. Gary Boyce
    Post

    Marlin for the R2 - UBL Enabled

    I am attempting this on a MKS GEN 1.4. I changed the board to // The following define selects which electronics board you have. // Please choose...
    Post by: Gary Boyce, Jan 13, 2019 in forum: Mods and Upgrades
  9. Gary Boyce
    Post

    3rd Party RAMPS

    Cool.. That's nice and easy
    Post by: Gary Boyce, Jan 13, 2019 in forum: Mods and Upgrades
  10. Gary Boyce
    Post

    3rd Party RAMPS

    Maybe I work slow.. but I'm still at it. For the -X, -Y, and +Z limit switches: They all have just 2 wires. Would I be right to assume that the...
    Post by: Gary Boyce, Jan 13, 2019 in forum: Mods and Upgrades
  11. Gary Boyce
    Post

    3rd Party RAMPS

    That's exactly what I needed!!! The pdf I uploaded shows the IR board pinout. Thanks Again!
    Post by: Gary Boyce, Jan 12, 2019 in forum: Mods and Upgrades
  12. Gary Boyce
    Post

    3rd Party RAMPS

    I got the MKS_Gen_V1.4 board. I have identified each wire/connection from the updown cable. The only thing I am uncertain of is the IR sensor...
    Post by: Gary Boyce, Jan 12, 2019 in forum: Mods and Upgrades
  13. Gary Boyce
    Post

    3rd Party RAMPS

    This is FANTASTIC! Thanks guys. I can always depend on great answers and suggestions from you two!
    Post by: Gary Boyce, Jan 1, 2019 in forum: Mods and Upgrades
  14. Gary Boyce
    Post

    3rd Party RAMPS

    This one seems to have a higher rating and I like that the Mega is integrated. I know I would still have to get the drivers, but what do think of...
    Post by: Gary Boyce, Jan 1, 2019 in forum: Mods and Upgrades
  15. Gary Boyce
    Post

    3rd Party RAMPS

    Thanks Mark! Would I be able to us the UBL with that as well? I guess I would have to break-out the cable that goes up to the extruder assembly....
    Post by: Gary Boyce, Jan 1, 2019 in forum: Mods and Upgrades
  16. Gary Boyce
    Thread

    3rd Party RAMPS

    Any suggestions for a 3rd party RAMPS board for the R2? I believe mine is broken. It can't turn the extruder motor and I have tried replacing the...
    Thread by: Gary Boyce, Jan 1, 2019, 22 replies, in forum: Mods and Upgrades
  17. Gary Boyce
    Post

    Poor Extrusion?

    Thanks!
    Post by: Gary Boyce, Oct 28, 2018 in forum: Troubleshooting
  18. Gary Boyce
    Thread

    Poor Extrusion?

    Can someone please tell me what is going on with this print? I am using new filament.
    Thread by: Gary Boyce, Oct 28, 2018, 3 replies, in forum: Troubleshooting
  19. Gary Boyce
    Post

    Very Frustrated. First layer, every layer, problems

    Just wanted to give an update.. One of the engineers from Robo contacted me this evening and I am back to printing! There was a problem with the...
    Post by: Gary Boyce, Jun 27, 2018 in forum: Troubleshooting
  20. Gary Boyce
    Post

    Very Frustrated. First layer, every layer, problems

    I know. You guys have been a fantastic help in getting to the bottom of this issue, and I appreciate your help tremendously. Just had to have a...
    Post by: Gary Boyce, Jun 26, 2018 in forum: Troubleshooting
Showing results 21 to 40 of 118 Next >
Search Again
Page 2 of 6