1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 4
  1. Larry Garrido
    Post

    Z-Axis Lead Screw Nut Replacement

    Thanks @WheresWaldo, I'll give those a try!
    Post by: Larry Garrido, Apr 30, 2019 in forum: General Questions
  2. Larry Garrido
    Thread

    Z-Axis Lead Screw Nut Replacement

    I'm looking to replace the lead screw nut for the Z-axis stepper and not sure what the correct lead screw pitch and lead the R2 uses, does anyone...
    Thread by: Larry Garrido, Apr 30, 2019, 2 replies, in forum: General Questions
  3. Larry Garrido
    Post

    Any success (or failure) with R2 and NylonX?

    Yikes! I dont think I have had the need to print anything that large with it yet and I mostly print on Garolite, I have used the purple glue...
    Post by: Larry Garrido, Apr 2, 2019 in forum: General Questions
  4. Larry Garrido
    Post

    Any success (or failure) with R2 and NylonX?

    I print with NylonX a lot on my R2, probably 5-6 rolls through it now and it prints beautifully! My R2 is modified with an E3D V6 and Titan...
    Post by: Larry Garrido, Apr 2, 2019 in forum: General Questions
  5. Larry Garrido
    Post

    List of Connectors used in the R2

    The pins for the V2 Bed harness connector: AMP TE 1-104479-3 (you will need a crimping tool to install them or you could solder them). LINK to...
    Post by: Larry Garrido, Jan 2, 2019 in forum: Projects
  6. Larry Garrido
    Post

    Does Anyone Want a Custom Glass Bed?

    I havent printed any straight nylon yet it's all been of the CF variety and the CF in it does stiffen it up to help prevent warping, It warps much...
    Post by: Larry Garrido, Jun 28, 2018 in forum: Mods and Upgrades
  7. Larry Garrido
    Post

    Does Anyone Want a Custom Glass Bed?

    I have been printing successfully with the PC CF filament (I believe it's Priline brand) using straight PEI sheet, this stuff likes to be squished...
    Post by: Larry Garrido, Jun 27, 2018 in forum: Mods and Upgrades
  8. Larry Garrido
    Post

    Clearing a deep throat hot-end jam

    just use one of these, should only take a second or two. [IMG]
    Post by: Larry Garrido, Jun 27, 2018 in forum: Troubleshooting
  9. Larry Garrido
    Post

    Is the E3D V6 compatible with R2?

    Of course, thats exactly how I was able to make the changes easily, it's only fair that I share what was intended to be shared to begin with!
    Post by: Larry Garrido, Jun 18, 2018 in forum: General Questions
  10. Larry Garrido
    Post

    Is the E3D V6 compatible with R2?

    Here is the link to the solid file: https://a360.co/2JVvhQo .STL is attached for slice and print.
    Post by: Larry Garrido, Jun 18, 2018 in forum: General Questions
  11. Larry Garrido
    Post

    Is the E3D V6 compatible with R2?

    Sure I'll upload them tomorrow when I get back in town.
    Post by: Larry Garrido, Jun 17, 2018 in forum: General Questions
  12. Larry Garrido
    Post

    E3Dv6 Replacement for Hexagon Hotend

    Anyone see this? Looks like a really nice solution. Robo R2 X/Y carriage E3dv6 Mod
    Post by: Larry Garrido, Jun 11, 2018 in forum: Mods and Upgrades
  13. Larry Garrido
    Post

    Bushings for X and Y axis rods

    Anyone find a source for these? I cant seem to find any that are 40mm, just 35mm.
    Post by: Larry Garrido, Jun 8, 2018 in forum: General Questions
  14. Larry Garrido
    Post

    G-Code Controlled Case Lighting

    Ok I'll give that a try...
    Post by: Larry Garrido, May 30, 2018 in forum: Mods and Upgrades
  15. Larry Garrido
    Post

    G-Code Controlled Case Lighting

    Ok so it the power + from fan 1 to be used as the signal wire?
    Post by: Larry Garrido, May 29, 2018 in forum: Mods and Upgrades
  16. Larry Garrido
    Post

    G-Code Controlled Case Lighting

    This is what Im trying to connect, main power is coming from the 24v board connection like in Waldo's first post. [IMG]
    Post by: Larry Garrido, May 29, 2018 in forum: Mods and Upgrades
  17. Larry Garrido
    Post

    G-Code Controlled Case Lighting

    Not really, unless Im looking at this wrong. Does the fan 1 connection on the board replace this connection in the original post? [IMG]
    Post by: Larry Garrido, May 29, 2018 in forum: Mods and Upgrades
  18. Larry Garrido
    Post

    G-Code Controlled Case Lighting

    Can you explain this with a bit more detail? I got remove fan2 (stock lights) and plug the main board fan (now in fan 1) into the fan2 position,...
    Post by: Larry Garrido, May 29, 2018 in forum: Mods and Upgrades
  19. Larry Garrido
    Post

    Is the E3D V6 compatible with R2?

    Of course!
    Post by: Larry Garrido, May 25, 2018 in forum: General Questions
  20. Larry Garrido
    Post

    Is the E3D V6 compatible with R2?

    Thanks! Here is the shroud, still tweaking it a bit though. Printed with NylonX [IMG]
    Post by: Larry Garrido, May 24, 2018 in forum: General Questions
Showing results 1 to 20 of 64 Next >
Search Again
Page 1 of 4