1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 10 of 10
  1. KTMDirtFace
    Post

    Time for Aluminum bed.

    I havn't used my printers in months, my robo with aluminum bed is still sitting as it was months ago. Started working on them tonight finally....
    Post by: KTMDirtFace, Feb 26, 2017 in forum: Mods and Upgrades
  2. KTMDirtFace
    Post

    Does anyone care about Makerbot anymore?

    I had a R2 modified with a heated bed, and it was a really really good machine. Then they went full retard and I haven't even paid any attention...
    Post by: KTMDirtFace, Feb 26, 2017 in forum: Off Topic
  3. KTMDirtFace
    Post

    Lattice Test

    Yea I will. Cool thanks! [img] [img]
    Post by: KTMDirtFace, Nov 6, 2016 in forum: Off Topic
  4. KTMDirtFace
    Thread

    Lattice Test

    Been watching Angus's videos with the lattice test. I'm not a patrion to him though I probably should be. But he was showing off prints that...
    Thread by: KTMDirtFace, Nov 5, 2016, 9 replies, in forum: Off Topic
  5. KTMDirtFace
    Post

    Time for Aluminum bed.

    I might have some Deans Wet Noodles from my RC stuff that will work and is super flexy. Thanks; I think its 12..
    Post by: KTMDirtFace, Oct 30, 2016 in forum: Mods and Upgrades
  6. KTMDirtFace
    Post

    Another printer (it is a disease, once you start collecting them...)

    Nice, "Why do you need another printer" somone asked at my house the other day. I had no real reason other than "it looked cool" or "I don't...
    Post by: KTMDirtFace, Oct 30, 2016 in forum: Projects
  7. KTMDirtFace
    Post

    Time for Aluminum bed.

    Ok eletric guru's what gauge wire should I use? I think i need a couple small bits to go from the solid state to the powersupply/AC input. I...
    Post by: KTMDirtFace, Oct 30, 2016 in forum: Mods and Upgrades
  8. KTMDirtFace
    Post

    Was - Linear Rails -Now making own printer

    Yea i watched his build videos.
    Post by: KTMDirtFace, Oct 26, 2016 in forum: Projects
  9. KTMDirtFace
    Post

    FPV Quadcopter - Accessories

    Sorry I missed this. My quads are 250 sized FPV Racing quads. I have a Blade 350 V3 with a Tarot Gimball, but I got BORED TO HELL with that...
    Post by: KTMDirtFace, Oct 26, 2016 in forum: Projects
  10. KTMDirtFace
    Post

    Linear bearings for X axis carriage

    I use this on my rails since I have it. Few drops every once in awhile...
    Post by: KTMDirtFace, Oct 26, 2016 in forum: Mods and Upgrades
  11. KTMDirtFace
    Post

    What's your opinion on Flexion extruder retrofit kit?

    FYI this was printed at 60mm/s on my Modified Replicator 2 which I no longer own. In ninja flex. no retraction. Also NEVER print ninja flex to...
    Post by: KTMDirtFace, Oct 17, 2016 in forum: Mods and Upgrades
  12. KTMDirtFace
    Post

    What's your opinion on Flexion extruder retrofit kit?

    I haven't used it a lot with flexibles, but yes I turned retraction off. and Printed at 30mm/s using NinjaFlex. I think it could print faster,...
    Post by: KTMDirtFace, Oct 17, 2016 in forum: Mods and Upgrades
  13. KTMDirtFace
    Post

    What's your opinion on Flexion extruder retrofit kit?

    I have a Titan Extruder on both of my Robo's. Prints flexible well, the only gotcha I found was keep the tension screw about one turn from full...
    Post by: KTMDirtFace, Oct 17, 2016 in forum: Mods and Upgrades
Find older messages
Showing results 181 to 193 of 193
Search Again
Page 10 of 10