1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 5 of 5
  1. Hanover
    Post

    Finding Parts for the R2 - What to look up

    Yes, there's a 2mm difference. I think I'm just going to go with an E3D clone by RepRap. That way there is less risk if I can't get it to work....
    Post by: Hanover, Aug 21, 2017 in forum: General Questions
  2. Hanover
    Post

    Finding Parts for the R2 - What to look up

    I think I was the first to replace the PEI. So there ya go. :)
    Post by: Hanover, Aug 21, 2017 in forum: General Questions
  3. Hanover
    Post

    Finding Parts for the R2 - What to look up

    Okay, well, after doing some research, I think I'm just going to go with the E3D Universal V6. It's kind of pricey, but like you said, I don't...
    Post by: Hanover, Aug 21, 2017 in forum: General Questions
  4. Hanover
    Post

    Finding Parts for the R2 - What to look up

    What about just ditching the stock hot end and replacing it with one that's less proprietary? Couldn't we replace it with something like this and...
    Post by: Hanover, Aug 21, 2017 in forum: General Questions
  5. Hanover
    Thread

    Finding Parts for the R2 - What to look up

    I've pretty much gotten the message that Robo will not have any spare parts for the R2 any time soon. So, if i was to look for the thermistor...
    Thread by: Hanover, Aug 21, 2017, 59 replies, in forum: General Questions
  6. Hanover
    Post

    Unclogging Documentation?

    Great idea! I'll wait to see what Robo says and order the C2 hot end if they can't send me an R2 version I'm glad I still have a working R1+!
    Post by: Hanover, Aug 20, 2017 in forum: Troubleshooting
  7. Hanover
    Post

    Unclogging Documentation?

    Well, you saw the result on the Facebook post. :) The wires going into the thermistor ended up getting pulled out. They were barely being held...
    Post by: Hanover, Aug 20, 2017 in forum: Troubleshooting
  8. Hanover
    Thread

    Unclogging Documentation?

    Right now I have a clogged extruder and have no idea how to take the extruder apart to unclog it. Where is the documentation that shows me how to...
    Thread by: Hanover, Aug 20, 2017, 7 replies, in forum: Troubleshooting
  9. Hanover
    Post

    PEI Print Bed Problem

    Don't use the putty knife or any other tool with a sharp/pointy metal end. :) I just replaced my PEI and the process wasn't very fun. Use a...
    Post by: Hanover, Aug 20, 2017 in forum: Troubleshooting
  10. Hanover
    Post

    R2 Print Bed

    After a bit of effort, I ended up getting the new PEI sheet onto the bed. Damn those 3M transfer sheets are sticky. :) The only issue now is...
    Post by: Hanover, Aug 18, 2017 in forum: Troubleshooting
  11. Hanover
    Post

    R2 Print Bed

    My adhesive is coming tomorrow, so I decided to try to remove the existing PEI tonight. I threw the bed into the freezer for about 40 minutes....
    Post by: Hanover, Aug 17, 2017 in forum: Troubleshooting
  12. Hanover
    Post

    R2 Print Bed

    After messing around with the Print Bed for a little bit, I figured out a few things: The four covers on the top that are covering the screws...
    Post by: Hanover, Aug 15, 2017 in forum: Troubleshooting
  13. Hanover
    Post

    Replacing the PEI sheet on the R2

    Do NOT try to pull off the covers on the top sides of the bed. Those are actually glued on. So I guess we just need to put the entire bed...
    Post by: Hanover, Aug 15, 2017 in forum: General Questions
  14. Hanover
    Post

    Replacing the PEI sheet on the R2

    I took a good look at the bed. The PEI is stuck to the aluminum and the heated part is screwed to the underside of the aluminum. The top of the...
    Post by: Hanover, Aug 15, 2017 in forum: General Questions
  15. Hanover
    Post

    R2 Print Bed

    Well, I send them a message and basically they just said I can replace it with a PEI sheet from Amazon. Apparently how it's done in an official...
    Post by: Hanover, Aug 13, 2017 in forum: Troubleshooting
  16. Hanover
    Post

    Replacing the PEI sheet on the R2

    Did you ever figure this out? I'm thinking its time to change the PEI on mine as well. I had sent an email to Robo and they just said remove it...
    Post by: Hanover, Aug 13, 2017 in forum: General Questions
  17. Hanover
    Post

    R2 Print Bed

    Anyone figure this out yet? Who can we ask at Robo for how to remove the PEI sheet and replace it? Mine is scratched bits of it are making the...
    Post by: Hanover, Jul 24, 2017 in forum: Troubleshooting
  18. Hanover
    Post

    Totally confused about the print Bed. PEI? Glass? Adhesion?

    Actually, mine has little nicks in it, creating an uneven surface right in the center. Does that mean I need to sand it? I have an extra 8x8 PEI...
    Post by: Hanover, Jul 24, 2017 in forum: General Questions
  19. Hanover
    Thread

    Totally confused about the print Bed. PEI? Glass? Adhesion?

    Hi there, I just need to understand. Is the black, glassy surface of the print bed PEI? Is it replaceable? After double and triple checking to...
    Thread by: Hanover, Jul 22, 2017, 5 replies, in forum: General Questions
Find older messages
Showing results 81 to 99 of 99
Search Again
Page 5 of 5