1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Carlos144Green
    Post

    Unresolved LCD Screen Non-responsive

    Oh really? could you send me the link please! I'll also try out the fix you recommended but the chances are that it isn't the problem because I...
    Post by: Carlos144Green, Nov 22, 2019 in forum: Troubleshooting
  2. Carlos144Green
    Post

    Unresolved LCD Screen Non-responsive

    I tried with a new 8 gb sd card with a fresh os. Same problems, menu screen shows but no touch inputs get through. I wasn't aware the warranty for...
    Post by: Carlos144Green, Nov 20, 2019 in forum: Troubleshooting
  3. Carlos144Green
    Thread

    Unresolved LCD Screen Non-responsive

    Hello! I'm back with another problem... So recently I decided to turn off my printer the proper way with the shutdown button through the menu of...
    Thread by: Carlos144Green, Nov 8, 2019, 8 replies, in forum: Troubleshooting
  4. Carlos144Green
    Post

    Partial Answer Many Layers Print Poorly

    I havent heard it skip yet so its narrowed down to these > (weak stepper driver, bad mainboard, bad wire, etc). I'll look into it once I start...
    Post by: Carlos144Green, Sep 8, 2019 in forum: Troubleshooting
  5. Carlos144Green
    Post

    Partial Answer Many Layers Print Poorly

    So I started using a completely new brand of pla and it started working again. The thing is that the motor feeding the filament is still making...
    Post by: Carlos144Green, Sep 8, 2019 in forum: Troubleshooting
  6. Carlos144Green
    Post

    Partial Answer Many Layers Print Poorly

    Turns out the filament was not the problem. Any other ideas?
    Post by: Carlos144Green, Sep 5, 2019 in forum: Troubleshooting
  7. Carlos144Green
    Post

    Partial Answer Many Layers Print Poorly

    The gear were already cleaned and tightened as much as they could be before that print. I haven't suspected the filament, I'll try with a new...
    Post by: Carlos144Green, Sep 5, 2019 in forum: Troubleshooting
  8. Carlos144Green
    Thread

    Partial Answer Many Layers Print Poorly

    So right off the bat, I know that this is not a hotend problem because I have replaced just about every part possible on the hotend with new parts...
    Thread by: Carlos144Green, Sep 5, 2019, 9 replies, in forum: Troubleshooting
  9. Carlos144Green
    Post

    Solved Extruding gear doesn't work with new part

    I tried both and it works :) That was a quick fix thanks!
    Post by: Carlos144Green, Apr 27, 2019 in forum: Troubleshooting
  10. Carlos144Green
    Thread

    Solved Extruding gear doesn't work with new part

    Recently I discovered my printer had a cracked part so I 3d printed a new part Robo designed. I popped it in and fit just fine. I ran a few tests...
    Thread by: Carlos144Green, Apr 26, 2019, 4 replies, in forum: Troubleshooting
  11. Carlos144Green
    Post

    Solved Prints come out slightly angled or stretched

    Worked! I used my old clips that came with the printer and quickly fixed it. I ran the wiping part of a print and it was straight. Thanks a ton...
    Post by: Carlos144Green, Apr 21, 2019 in forum: Troubleshooting
  12. Carlos144Green
    Post

    Solved Prints come out slightly angled or stretched

    I didn't think of that, I'll test it out tomorrow and post what the outcome is.
    Post by: Carlos144Green, Apr 21, 2019 in forum: Troubleshooting
  13. Carlos144Green
    Thread

    Solved Prints come out slightly angled or stretched

    I don't know for how long but I have noticed this with my prints. Squares and other orthogonal shapes are clearly not at 90 degrees angles. My...
    Thread by: Carlos144Green, Apr 21, 2019, 10 replies, in forum: Troubleshooting
  14. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    It worked!! Thanks to everyone who walked me through this. Every piece of advice was useful in the end since it led me to check the feeding gear.
    Post by: Carlos144Green, Apr 14, 2019 in forum: Troubleshooting
  15. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    So I saw this crack behind my bearing and shield when I was inspecting closer at the feeding mechanism. This may be the root cause of all my...
    Post by: Carlos144Green, Apr 14, 2019 in forum: Troubleshooting
  16. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    The nozzle is .4mm and I have printed with this type for a long time without problems.
    Post by: Carlos144Green, Apr 14, 2019 in forum: Troubleshooting
  17. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    Didn't work.
    Post by: Carlos144Green, Apr 14, 2019 in forum: Troubleshooting
  18. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    I checked the fan capabilities and they all check out (video below). I also did another cold pull and there seems to be no more residue at all...
    Post by: Carlos144Green, Apr 14, 2019 in forum: Troubleshooting
  19. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    Still the same problem.
    Post by: Carlos144Green, Apr 13, 2019 in forum: Troubleshooting
  20. Carlos144Green
    Post

    Solved Filament not extruding even with new extruder

    I used great value vegetable oil and followed the steps below after cold pull cleaning. http://www.dragonflydiy.com/2014/06/nozzle-seasoning.html
    Post by: Carlos144Green, Apr 13, 2019 in forum: Troubleshooting
Showing results 1 to 20 of 29 Next >
Search Again
Page 1 of 2