1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. jscottb
    Post

    R2 Bed is kind of fiddly...

    I think it comes down to a marginal design, or at the very least a rushed one. The Pogo pins may be adding some to the issue. Those springs may...
    Post by: jscottb, Oct 18, 2017 in forum: Troubleshooting
  2. jscottb
    Thread

    R2 Bed is kind of fiddly...

    Hello, I have had my R2 for a few weeks now and really like it a lot. It prints great. But... The bed needs leveling just about every print. I...
    Thread by: jscottb, Oct 18, 2017, 16 replies, in forum: Troubleshooting
  3. jscottb
    Post

    Robo R2 Creating 100% Infill when 15% is Specified in Cura

    Are you generating a gcode file and sending that to the printer or are you sending the .stl file to it? You will want to send a gcode file if you...
    Post by: jscottb, Oct 2, 2017 in forum: General Questions
  4. jscottb
    Post

    Robo R2 Creating 100% Infill when 15% is Specified in Cura

    It would be in the slicer options you are using. Are you slicing with a local copy of Cura, or sending the STL to the printer and getting...
    Post by: jscottb, Oct 1, 2017 in forum: General Questions
  5. jscottb
    Post

    Z-screw stabilizer plug

    The plug fits snugly into the holes and just touches the rod on the inside. I have not had any issues with spinning on mine.
    Post by: jscottb, Sep 26, 2017 in forum: Mods and Upgrades
  6. jscottb
    Post

    R2 received and in production!

    I have no issues with the bed being off and am fine with it as long as it consistent, and it seems to be. The octoprint profiles have been changed...
    Post by: jscottb, Sep 19, 2017 in forum: Show and Tell
  7. jscottb
    Post

    R2 received and in production!

    Forgot a pic.[IMG] Sent from my SM-G900V using Tapatalk
    Post by: jscottb, Sep 18, 2017 in forum: Show and Tell
  8. jscottb
    Post

    R2 received and in production!

    Oh, the temperature test was on the bed. Sent from my SM-G900V using Tapatalk
    Post by: jscottb, Sep 18, 2017 in forum: Show and Tell
  9. jscottb
    Post

    R2 received and in production!

    Well, I have finally printed a Benchy. Not prefect but not too bad. I did do some temp test and it's off around 14 degrees +/- 2 deg. I measured...
    Post by: jscottb, Sep 18, 2017 in forum: Show and Tell
  10. jscottb
    Post

    R2 received and in production!

    I decided to use the power of the internets and my printers... I found this one on Thingiverse https://www.thingiverse.com/make:383593 and did a...
    Post by: jscottb, Sep 17, 2017 in forum: Show and Tell
  11. jscottb
    Post

    R2 received and in production!

    Yeah, I plan to get one from the auto parts store this week :) I do think the temp is off on the bed a good bit. I have been resetting the offset...
    Post by: jscottb, Sep 17, 2017 in forum: Show and Tell
  12. jscottb
    Post

    R2 received and in production!

    My thoughts after a couple of days and a lot of printing... I like it a lot! There are things I like less about it, for one the print bed. It...
    Post by: jscottb, Sep 17, 2017 in forum: Show and Tell
  13. jscottb
    Thread

    Z-screw stabilizer plug

    I hate wobbly rods :) So here is a simple plug to keep the z screw from wobbling. If you print it, let me know of any issues....
    Thread by: jscottb, Sep 16, 2017, 5 replies, in forum: Mods and Upgrades
  14. jscottb
    Post

    The rpi password for user pi is still set to the default

    Yes, my main point (that I so poorly conveyed) is that this should be changed on all RPI's or any other SBC you have. Many may not know that there...
    Post by: jscottb, Sep 16, 2017 in forum: Software
  15. jscottb
    Post

    The rpi password for user pi is still set to the default

    Yeah, I had changed mine to see and it seemed fine after a test reboot.
    Post by: jscottb, Sep 15, 2017 in forum: Software
  16. jscottb
    Thread

    The rpi password for user pi is still set to the default

    I would look to changing this to something else. I would hope it's not used anywhere in the Robo3d addons or mods for Octoprint. Just an FYI...
    Thread by: jscottb, Sep 15, 2017, 6 replies, in forum: Software
  17. jscottb
    Post

    Joel Telling's video on heat creep in the R2

    I did just get my R2, but have read and watched about the heat creep issues with the it. I had HC issues on my old printrbot. Between the extruder...
    Post by: jscottb, Sep 15, 2017 in forum: Troubleshooting
  18. jscottb
    Thread

    R2 received and in production!

    I have my new R2 and it came in good condition. There was only one small issue... The boxes inside pressed against the X stepper connection and...
    Thread by: jscottb, Sep 15, 2017, 26 replies, in forum: Show and Tell
Find older messages
Showing results 21 to 38 of 38
Search Again
Page 2 of 2