1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    I'm using one of these with a meanwell 24V PSU. https://tinyurl.com/jral2zm Now my bed goes from 25c to 90c in 5 minutes. And it was super easy...
    Post by: Tom Finzel, Feb 14, 2017 in forum: Mods and Upgrades
  2. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    [MEDIA]
    Post by: Tom Finzel, Feb 13, 2017 in forum: Mods and Upgrades
  3. Tom Finzel
    Post

    Solved Still - Y axis only moving in one direction

    Turns out it was my Ardruino board. Flashed the firmware onto a Microcenter Arduino board and mounted my original Robo R1+ RAMPS board and I'm...
    Post by: Tom Finzel, Feb 7, 2017 in forum: Troubleshooting
  4. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    nope, one of these....
    Post by: Tom Finzel, Feb 7, 2017 in forum: Mods and Upgrades
  5. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    [ATTACH]
    Post by: Tom Finzel, Feb 7, 2017 in forum: Mods and Upgrades
  6. Tom Finzel
    Thread

    Solved Still - Y axis only moving in one direction

    Ok, I don't know how to ref my other thread since I marked it solved but it was titled Y axis only moving in one direction. I swapped the Robo...
    Thread by: Tom Finzel, Feb 6, 2017, 1 replies, in forum: Troubleshooting
  7. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    I ordered the 100A DC-DC from the link and it only lasted for a couple of test heat ups of the bed. No more red light on the SSR and bed heats...
    Post by: Tom Finzel, Feb 6, 2017 in forum: Mods and Upgrades
  8. Tom Finzel
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Ok, I'm confused and I'm not sure if this matters but the below picture looks to have a different wiring configuration. Thoughts??...
    Post by: Tom Finzel, Feb 3, 2017 in forum: Mods and Upgrades
  9. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    Thanks Geof, will do.
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  10. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    Thanks again for your help!
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  11. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    Yes, it was printing great yesterday on a cold bed using PLA. Swapped the connector for the heated bed today and it has this issue. The generic...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  12. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    No, nothing is blocking the y home switch as I can hear it click when I manually home it. I've never even looked at the firmware so no changes...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  13. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    When I home the y axis it goes to home and just grinds away and ignores the limit switch. I had to kill the power. I have spare stepper motors...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  14. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    I pretty sure nothing is blocking the y limit switch.,I can see it and hear it engage and disengage. I've ordered a ne ramps board from Amazon and...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  15. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    >M119 <-Reporting endstop status <-x_min: TRIGGERED <-y_min: TRIGGERED <-z_min: TRIGGERED <-ok ->M105 Y not homed + ->M119 <-Reporting endstop...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  16. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    After I rewired the RAMPS the endstop message went away. See new snippet above. Could it be the step driver? Thanks again dude! Any Y - and Y...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  17. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    I already tested the endstop switch with my meter and it works. RAMPS Huh?
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  18. Tom Finzel
    Post

    Solved Y axis only moving in one direction

    Looks like they are connected correctly. I reconnected all the wiring and same results. Thanks for your help Mark! Edit: Not exactly the same...
    Post by: Tom Finzel, Jan 30, 2017 in forum: Troubleshooting
  19. Tom Finzel
    Post

    Changing Filament Color mid-print

    Yo cold also try this http://www.prusaprinters.org/color-print/ There is a guy n the Robo3d FB group that is making some awesome multicolor prints.
    Post by: Tom Finzel, Jan 30, 2017 in forum: General Questions
  20. Tom Finzel
    Thread

    Solved Y axis only moving in one direction

    Hey Guys, The heated bed connector on my RAMPS board for my R1 Plus fried so I replaced it and now the Y axis only moves in one direction. I...
    Thread by: Tom Finzel, Jan 30, 2017, 24 replies, in forum: Troubleshooting
Showing results 1 to 20 of 36 Next >
Search Again
Page 1 of 2