1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Tom Finzel
    Post

    Partial Answer Printing from SD Card

    Try this: Export your Gcode to an SD card and rename it auto0.g Power off the Robo and insert the SD card and power on the Robo. Wait......
    Post by: Tom Finzel, Apr 13, 2016 in forum: Troubleshooting
  2. Tom Finzel
    Post

    Unanswered Robo seems to lose track of Y axis while printing

    You might want to check and see if the small gear attached to the shaft of the Y stepper motor that drives the belt is tight.
    Post by: Tom Finzel, Apr 10, 2016 in forum: Troubleshooting
  3. Tom Finzel
    Post

    Unresolved Under extrusion issue

    hmmm, try this [MEDIA]
    Post by: Tom Finzel, Apr 7, 2016 in forum: Troubleshooting
  4. Tom Finzel
    Post

    Unresolved Under extrusion issue

    try changing your offset to 0.8.
    Post by: Tom Finzel, Apr 7, 2016 in forum: Troubleshooting
  5. Tom Finzel
    Post

    Solved printing in the air!

    Did you try this: To do this you just need to lower the Z Axis a couple of millimeters from the bed and slide the extruder to one side. Now pay...
    Post by: Tom Finzel, Mar 18, 2016 in forum: Troubleshooting
  6. Tom Finzel
    Post

    E3D v6 Information, Installation Guides, and Review

    If you used the screw in stud thermister than no. If you used the the other one then yes and the firmware changes are covered in this thread. I...
    Post by: Tom Finzel, Mar 16, 2016 in forum: Mods and Upgrades
  7. Tom Finzel
    Post

    E3D v6 Information, Installation Guides, and Review

    One way is to change your Z offset in the Controls screen/macros. Default is 0.9 so try 1.0. It is a sticky setting so it persists from print to...
    Post by: Tom Finzel, Mar 16, 2016 in forum: Mods and Upgrades
  8. Tom Finzel
    Post

    Solved Bubbling on bed, where do I start?

    Yes, it will make the nozzle closer to the bed. :)
    Post by: Tom Finzel, Mar 15, 2016 in forum: Troubleshooting
  9. Tom Finzel
    Post

    Solved Bubbling on bed, where do I start?

    If you are using MatterControl trying changing the z offset to 0.8. The default is 0.9 Look under controls/macros towards the bottom. Just click...
    Post by: Tom Finzel, Mar 15, 2016 in forum: Troubleshooting
  10. Tom Finzel
    Post

    Solved Zebra Plate versus auto-leveling

    My Zebra Plate is on it's way so I tried this gcode and it works perfectly. Thanks!
    Post by: Tom Finzel, Mar 8, 2016 in forum: Troubleshooting
  11. Tom Finzel
    Post

    Changing Filament Color mid-print

    http://www.mattercontrol.com/#jumpMatterControlDownloads
    Post by: Tom Finzel, Mar 7, 2016 in forum: General Questions
  12. Tom Finzel
    Post

    Question... How do I make supports easier to remove?

    Generate support using Meshmixer. Very easy to remove and you can customize the support. [MEDIA]
    Post by: Tom Finzel, Mar 7, 2016 in forum: General Questions
  13. Tom Finzel
    Post

    Changing Filament Color mid-print

    Upgrade to Mattercontrol 1.5 There is a pause layer option now under settings/general/layers/surface. Make sure you have the advanced option enabled.
    Post by: Tom Finzel, Mar 7, 2016 in forum: General Questions
  14. Tom Finzel
    Post

    Solved Z Axis WAYYYY off after hot end replacement

    David I posted a dropbox pic link to your profile page showing the routing of the wires from my stock R1 plus. HTH
    Post by: Tom Finzel, Feb 7, 2016 in forum: Troubleshooting
  15. Tom Finzel
    Post

    Solved Z Axis WAYYYY off after hot end replacement

    Post by: Tom Finzel, Feb 7, 2016 in forum: Troubleshooting
  16. Tom Finzel
    Profile Post

    I'm a new member too but here is a pic of the R1 plus extruder factory routing of the wire....

    I'm a new member too but here is a pic of the R1 plus extruder factory routing of the wire....
    Profile post by Tom Finzel for David Carter, Feb 7, 2016
Find older messages
Showing results 21 to 36 of 36
Search Again
Page 2 of 2