1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 5
  1. TomerO
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Question: why isn't there simply a Robo3d fork of marlin? If it's a technical/knowhow thing I will gladly help (once I'm done setting up my new...
    Post by: TomerO, Jun 10, 2016 in forum: Mods and Upgrades
  2. TomerO
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Maybe I didn't understand something, since I didn't have to play with it a lot. Will you explain to me what the difference is? Except the effect...
    Post by: TomerO, Jun 8, 2016 in forum: Troubleshooting
  3. TomerO
    Post

    Solved Simplify3D Print Bed Calibration Issues

    Just dropped by to say that it doesn't sound like a bug to me. S3D provides gcode offset setting to all axis so you can set a z offset directly in...
    Post by: TomerO, Jun 8, 2016 in forum: Troubleshooting
  4. TomerO
    Post

    Unanswered Brittle Filament

    Thx. I guess that 60-90% humidity is a PLA killer =] Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 8, 2016 in forum: Troubleshooting
  5. TomerO
    Post

    Unanswered Brittle Filament

    Interesting. It's still printing fine so I'm not going to discard it. Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 8, 2016 in forum: Troubleshooting
  6. TomerO
    Post

    Unanswered Brittle Filament

    If that was true why would it be stiff? Also, why would it happen only in bent places? Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 7, 2016 in forum: Troubleshooting
  7. TomerO
    Post

    Unanswered Brittle Filament

    Removing will work obviously. I will try to align it after a print and see. Thinking about it, it might also related to the spring that holds the...
    Post by: TomerO, Jun 7, 2016 in forum: Troubleshooting
  8. TomerO
    Thread

    Unanswered Brittle Filament

    Hey, It is nothing new, but I decided it is time to maybe address this issue. Some of my filament rolls (all eSun PLA) tend to break when sitting...
    Thread by: TomerO, Jun 7, 2016, 12 replies, in forum: Troubleshooting
  9. TomerO
    Post

    Unanswered Strange noise just started, aka Stepper drive from Hades

    The stepper driver is one of the parts on the RAMPS board at the bottom. Did you try to test the stepper disassembled? Sent from my Nexus 5 using...
    Post by: TomerO, Jun 7, 2016 in forum: Troubleshooting
  10. TomerO
    Post

    Unresolved I think I've killed it!

    I fucked up my axis the same way you did on my first day with the printer. Just popped it back to place, but listen to geof Good luck! Sent...
    Post by: TomerO, Jun 7, 2016 in forum: Troubleshooting
  11. TomerO
    Post

    DIY Fleks 3D (type) build plate - no glue, no hairspray

    I added a +0.4 z offset in S3D and it worked out nice on the sanded side :) Easy to take off and all. I might add even more (a bit) since first...
    Post by: TomerO, Jun 6, 2016 in forum: Show and Tell
  12. TomerO
    Post

    DIY Fleks 3D (type) build plate - no glue, no hairspray

    Might do that. Although that side of the build plate might be lost Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 6, 2016 in forum: Show and Tell
  13. TomerO
    Post

    DIY Fleks 3D (type) build plate - no glue, no hairspray

    I found a problem with my leveling but it wasn't it. The last test completely merged to the build... lots of sanding bah... I bought mine from...
    Post by: TomerO, Jun 6, 2016 in forum: Show and Tell
  14. TomerO
    Post

    DIY Fleks 3D (type) build plate - no glue, no hairspray

    My problem was a faulty program (that I wrote) but no biggie. I will try to level the printer again and see what happens. Also, not all plastics...
    Post by: TomerO, Jun 6, 2016 in forum: Show and Tell
  15. TomerO
    Post

    Unanswered Strange noise just started, aka Stepper drive from Hades

    Does this happen only when printing? Does it begin from the start? It sounds like either a motor is stuck/have something in it or a cable touching...
    Post by: TomerO, Jun 6, 2016 in forum: Troubleshooting
  16. TomerO
    Post

    DIY Fleks 3D (type) build plate - no glue, no hairspray

    Update: I was testing some software thing and burnt a whole in my plate :( I decided to use that to test making the surface not smooth so I...
    Post by: TomerO, Jun 6, 2016 in forum: Show and Tell
  17. TomerO
    Thread

    Serial through raspberry pi

    (Note: I'm mainly sharing what I did, no time to actually upload the stuff now + question at the end) Hey guys, I am recently working (mainly for...
    Thread by: TomerO, Jun 5, 2016, 3 replies, in forum: Software
  18. TomerO
    Post

    First Major project.

    Nice. Let us know when you have more progress Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, Jun 4, 2016 in forum: Show and Tell
  19. TomerO
    Post

    E3D v6 Information, Installation Guides, and Review

    You should be able to see older releases there somewhere Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, May 31, 2016 in forum: Mods and Upgrades
  20. TomerO
    Post

    E3D v6 Information, Installation Guides, and Review

    True Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, May 31, 2016 in forum: Mods and Upgrades
Showing results 41 to 60 of 97 Next >
Search Again
Page 3 of 5