1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 9
  1. Chuck Erwin
    Post

    Prints with .15 E3D nozzle on r1+

    Yes,no not lost pla molds but making a mold out of it. But I believe there is a wax like filament for doing that.. I don't think there are any...
    Post by: Chuck Erwin, Dec 11, 2016 in forum: Projects
  2. Chuck Erwin
    Post

    Prints with .15 E3D nozzle on r1+

    I heard of a few doing this for jewelry.
    Post by: Chuck Erwin, Dec 11, 2016 in forum: Projects
  3. Chuck Erwin
    Post

    Unresolved Printer Missing Spots during print

    I am not sure what I am looking at either but here is a stab: Are you talking about the diagonal infill lines? If so try increasing your number of...
    Post by: Chuck Erwin, Dec 10, 2016 in forum: Troubleshooting
  4. Chuck Erwin
    Post

    Solved Problems since installing E3d V6

    Just curious what instructions did you follow? Also did you readjust your z-offset when you changed the to the E3d v6?
    Post by: Chuck Erwin, Dec 9, 2016 in forum: Troubleshooting
  5. Chuck Erwin
    Post

    Lattice Test

    Did you put any post gcode in?
    Post by: Chuck Erwin, Nov 27, 2016 in forum: Off Topic
  6. Chuck Erwin
    Post

    Simplify 3d

    Good to know.
    Post by: Chuck Erwin, Nov 23, 2016 in forum: Software
  7. Chuck Erwin
    Post

    Simplify 3d

    Good work, when i get time I'll try it. Prusa puts out their color print but it is probably specific to the I3....
    Post by: Chuck Erwin, Nov 22, 2016 in forum: Software
  8. Chuck Erwin
    Post

    Unresolved calibrating print quality.

    I hope you got it.
    Post by: Chuck Erwin, Nov 19, 2016 in forum: Troubleshooting
  9. Chuck Erwin
    Post

    Unresolved calibrating print quality.

    The teeth do wear down and can slip a little causing problems. Well hopefully you don't have the problem I had Prints were coming out really bad....
    Post by: Chuck Erwin, Nov 19, 2016 in forum: Troubleshooting
  10. Chuck Erwin
    Post

    Unresolved calibrating print quality.

    Well they should have a little pluck to it but not super tight. Don't forget there are two belts to check one is under the bed. Plus if they are...
    Post by: Chuck Erwin, Nov 18, 2016 in forum: Troubleshooting
  11. Chuck Erwin
    Post

    Unresolved calibrating print quality.

    Did you check the tension on your belts?
    Post by: Chuck Erwin, Nov 18, 2016 in forum: Troubleshooting
  12. Chuck Erwin
    Post

    PLA stronghero3d GT-PLA and GoldX PLA review

    Well it looks good but I feel I am reading a commercial. What I am looking for is a good price for better PLA. I don't want to pay over $45.00 a...
    Post by: Chuck Erwin, Nov 16, 2016 in forum: Printing Filament
  13. Chuck Erwin
    Post

    Part required - Top part which attached to X Carriage R1

    I think you buy it first then you get two weeks to make up your mind. Try it for a full two weeks! If you don’t love the software, return it for...
    Post by: Chuck Erwin, Nov 11, 2016 in forum: Mods and Upgrades
  14. Chuck Erwin
    Post

    PLA Makergeeks Raptor PLA - high heat

    I have no problem with their filament esp the Raptor series but their shipping can be horrible, I bought the 4 roll grab bag pla and petg about a...
    Post by: Chuck Erwin, Nov 9, 2016 in forum: Printing Filament
  15. Chuck Erwin
    Post

    Another printer (it is a disease, once you start collecting them...)

    If I buy another printer my wife might cure the disease and bury me with it. I really do want to get a delta some day.... .... I'll have to be...
    Post by: Chuck Erwin, Nov 1, 2016 in forum: Projects
  16. Chuck Erwin
    Post

    Drying filament

    Yes probably but with fancy gauges and knobs.
    Post by: Chuck Erwin, Oct 25, 2016 in forum: Projects
  17. Chuck Erwin
    Post

    Drying filament

    There is a kick starter filament dryer. I don't know if it's any good or not just throwing it out there....
    Post by: Chuck Erwin, Oct 24, 2016 in forum: Projects
  18. Chuck Erwin
    Post

    Solved Will Not Extrude When Temp Is 185

    I usually print PLA at 190-215 you are on the really low side of melting it.
    Post by: Chuck Erwin, Oct 21, 2016 in forum: Troubleshooting
  19. Chuck Erwin
    Post

    Partially Solved 1st level and ledding, checking, LED modding

    I am not sure about the other angles but the nozzle angle "B" should be at right angles. It shouldn't hit the bed at an angle. I would use a...
    Post by: Chuck Erwin, Oct 14, 2016 in forum: Troubleshooting
  20. Chuck Erwin
    Post

    Partially Solved 1st level and ledding, checking, LED modding

    I just looked at mine and well it looks squared up. I am no expert but I am going with "no that's not normal" but I can't tell from the picture...
    Post by: Chuck Erwin, Oct 14, 2016 in forum: Troubleshooting
Showing results 21 to 40 of 168 Next >
Search Again
Page 2 of 9