1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 10
  1. tkoco
    Post

    How to fix: after 10-15 minutes the hotend temp regulation goes bad

    By any chance, do you have some sort of post-processing enabled in your slicing software? The last image posted suggest a post-processing issue...
    Post by: tkoco, Apr 9, 2020 in forum: Mods and Upgrades
  2. tkoco
    Post

    How to fix: after 10-15 minutes the hotend temp regulation goes bad

    And it might be model dependent, possibly redirecting the cooling fan air to the hot-end, or not as printing progresses.
    Post by: tkoco, Apr 8, 2020 in forum: Mods and Upgrades
  3. tkoco
    Post

    Filament FAQ

    Problems which you can find in no-name generic filaments: filament which is not round ( elliptical instead ), filament which has absorbed too much...
    Post by: tkoco, Apr 8, 2020 in forum: Filament
  4. tkoco
    Post

    Filament FAQ

    Filaments stored for more than a year without being used will tend to conform to the spool. These filaments can break when attempting to...
    Post by: tkoco, Apr 8, 2020 in forum: Filament
  5. tkoco
    Thread

    Filament FAQ

    This thread will be updated as new information comes to light. All plastics absorb water. The degree with which they absorb water will vary...
    Thread by: tkoco, Apr 8, 2020, 6 replies, in forum: Filament
  6. tkoco
    Post

    How to fix: after 10-15 minutes the hotend temp regulation goes bad

    The only factor which I can think of is the PID control loop is regulated too tightly. And once the heater block gets outside of the ability of...
    Post by: tkoco, Apr 8, 2020 in forum: Mods and Upgrades
  7. tkoco
    Post

    Calibrated Bed and Z Offset, weird clicking no prints

    Based on the video, the hot-end is clogged.
    Post by: tkoco, Apr 8, 2020 in forum: Troubleshooting
  8. tkoco
    Post

    Calibrated Bed and Z Offset, weird clicking no prints

    One of the items which experienced guys will tell you is that cheap filaments can be bad for printing. Problems like filament which is not round (...
    Post by: tkoco, Apr 8, 2020 in forum: Troubleshooting
  9. tkoco
    Post

    How to adjust print speed?

    The default Cura Engine for Robo is very old. The best way to access all the parameters for controlling the print job is to use a desktop / laptop...
    Post by: tkoco, Apr 7, 2020 in forum: General Questions
  10. tkoco
    Post

    GCode (Newbie)

    If you decide to use the Cura Start Sequence G-code, add a G29 ; Home the axis right after the G92 E0 G-code That way, all movements afterward...
    Post by: tkoco, Apr 7, 2020 in forum: Troubleshooting
  11. tkoco
    Post

    Non-Robo printers

    Thank you for the link. Certainly good information.
    Post by: tkoco, Apr 5, 2020 in forum: Off Topic
  12. tkoco
    Post

    Non-Robo printers

    Is Cartesian a brand or style?
    Post by: tkoco, Apr 5, 2020 in forum: Off Topic
  13. tkoco
    Post

    Inventor printing issue

    @mark tomlinson is correct. The other work-around for a model being too small is to use the scaling function built into the slicer programs ( like...
    Post by: tkoco, Apr 5, 2020 in forum: Troubleshooting
  14. tkoco
    Post

    Z-Offset Wizard stuck at step 1 of 4

    You are correct about the occasional delay to responding to a screen tap, but it is a minor thing. You are not obligated to use the script,...
    Post by: tkoco, Apr 5, 2020 in forum: Troubleshooting
  15. tkoco
    Thread

    Non-Robo printers

    @Geof , @mark tomlinson , @WheresWaldo and anyone else: Aside from resin printers, in your experience, What would be a good non-Robo, consumer...
    Thread by: tkoco, Apr 5, 2020, 8 replies, in forum: Off Topic
  16. tkoco
    Profile Post

    Busy Printing 8)

    Busy Printing 8)
    Status update by tkoco, Apr 5, 2020
  17. tkoco
    Thread

    R2 Lighting during printing

    This thread is a place holder for a project of mine to address the lighting of the print job in progress. I've already done the "Proof Of Concept"...
    Thread by: tkoco, Apr 4, 2020, 6 replies, in forum: Mods and Upgrades
  18. tkoco
    Post

    Test your printers clearance and tolerance by Maker's Muse

    I'll have to watch that video :)
    Post by: tkoco, Apr 4, 2020 in forum: Show and Tell
  19. tkoco
    Post

    Auto Tuning without damaging Flexplate System

    Thank you for explaining the situation. I was not aware of these issues.
    Post by: tkoco, Apr 4, 2020 in forum: Mods and Upgrades
  20. tkoco
    Post

    Z-Offset Wizard stuck at step 1 of 4

    @wuidling, The two pieces of the puzzle, RoboOS and Robo modified Marlin firmware, need to be matched up. I undertook a lot of testing of both...
    Post by: tkoco, Apr 4, 2020 in forum: Troubleshooting
Showing results 1 to 20 of 190 Next >
Search Again
Page 1 of 10