1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 5
  1. robert albrecht
    Post

    Solved Printing stop mid print.

    *edit* Ok inching closer. I figured out why it wasn't uploading. I was using arduino 1.8.8(?) I had to use an earlier version 1.6.9 (I think it...
    Post by: robert albrecht, Mar 1, 2019 in forum: Troubleshooting
  2. robert albrecht
    Post

    Solved Printing stop mid print.

    I have looked at the thread. The person who wrote it is assuming the reader knows how to to get into the arduino and change code. Or where to get...
    Post by: robert albrecht, Mar 1, 2019 in forum: Troubleshooting
  3. robert albrecht
    Post

    Solved Printing stop mid print.

    OK I am almost done. Now all I have left to do is update the firmware for the thermistor. I have looked over the guide. But I am still not sure...
    Post by: robert albrecht, Mar 1, 2019 in forum: Troubleshooting
  4. robert albrecht
    Post

    Solved Printing stop mid print.

    I am putting together my v6 and the thermistor is the tube type. Do I still have to change the type in the soft wear?[IMG] Sent from my SM-G950U...
    Post by: robert albrecht, Mar 1, 2019 in forum: Troubleshooting
  5. robert albrecht
    Post

    Solved I think my circuit card (ramps?) is over heating...Just want to confirm.

    I figured out what what was going on( I think) when I hooked up my USB cable for my Raspberry Pie. I had to move the Ramps board down a few...
    Post by: robert albrecht, Mar 1, 2019 in forum: Troubleshooting
  6. robert albrecht
    Thread

    Solved I think my circuit card (ramps?) is over heating...Just want to confirm.

    Ok now this is a little bit more serious. I am still getting the temp fall error. But tonight when I came out. My printer was stalled the lights...
    Thread by: robert albrecht, Feb 28, 2019, 3 replies, in forum: Troubleshooting
  7. robert albrecht
    Post

    Solved Here I am again... Print head dragging accross painters tape.

    Now it seems like I am getting contradicting advice LOL
    Post by: robert albrecht, Feb 28, 2019 in forum: Troubleshooting
  8. robert albrecht
    Post

    Solved Here I am again... Print head dragging accross painters tape.

    Ok. I have gotten into the habit of auto homing before each print. This isn't really necessary. Got it just don't auto home and I should be...
    Post by: robert albrecht, Feb 28, 2019 in forum: Troubleshooting
  9. robert albrecht
    Post

    Solved Here I am again... Print head dragging accross painters tape.

    Ughhh so confused LOL. With my printer should I be using only one interface exclusively as to not confuse the printer? (I have a riprap smart...
    Post by: robert albrecht, Feb 28, 2019 in forum: Troubleshooting
  10. robert albrecht
    Post

    Solved Here I am again... Print head dragging accross painters tape.

    So done this way. It will take the new z offset into consideration when ever I start a new print (even if I am using Astroprint for my primary...
    Post by: robert albrecht, Feb 28, 2019 in forum: Troubleshooting
  11. robert albrecht
    Post

    Solved Here I am again... Print head dragging accross painters tape.

    That's what I am thinking. But I dont have my laptop hooked up. Could this be done with my smart controller? (Riprap) Sent from my SM-G950U using...
    Post by: robert albrecht, Feb 27, 2019 in forum: Troubleshooting
  12. robert albrecht
    Thread

    Solved Here I am again... Print head dragging accross painters tape.

    So everybody has helped me with, cracked print bed,bad thermistor and a few other things. I think I have one more issue I need help with and then...
    Thread by: robert albrecht, Feb 27, 2019, 15 replies, in forum: Troubleshooting
  13. robert albrecht
    Post

    Solved Printing stop mid print.

    While I have a few people here. Let me ask what software should I be using? I am currently using Astroprint. The laptop I use is currently in my...
    Post by: robert albrecht, Feb 26, 2019 in forum: Troubleshooting
  14. robert albrecht
    Post

    Solved Printing stop mid print.

    Well was able to coax one more print out of her. Printed in PETG. That should be fine right??[IMG] Sent from my SM-G950U using Tapatalk
    Post by: robert albrecht, Feb 26, 2019 in forum: Troubleshooting
  15. robert albrecht
    Post

    Solved Printing stop mid print.

    Thanks for the help everybody. I know I have started several help needed threads over the last few days.(I guess it comes with the territory of...
    Post by: robert albrecht, Feb 26, 2019 in forum: Troubleshooting
  16. robert albrecht
    Post

    Solved Printing stop mid print.

    I went a head and ordered a E3DV6 off of Amazon. I double checked with the E3D website and the seller I purchased from is a Genuine E3D Reseller...
    Post by: robert albrecht, Feb 26, 2019 in forum: Troubleshooting
  17. robert albrecht
    Post

    Solved Printing stop mid print.

    I think I may need a new thermsistor and I am guessing since Robo no longer carries the hotend they prob do not carry the thermsistor any more.....
    Post by: robert albrecht, Feb 25, 2019 in forum: Troubleshooting
  18. robert albrecht
    Post

    Solved quick stupid question.

    That's what I thought.. thanks Sent from my SM-G950U using Tapatalk
    Post by: robert albrecht, Feb 25, 2019 in forum: Troubleshooting
  19. robert albrecht
    Thread

    Solved Printing stop mid print.

    Something weird is happening. During a print using PETG 235 extruder 80 print bed. Its stoping mid print and I am getting this error message on my...
    Thread by: robert albrecht, Feb 25, 2019, 75 replies, in forum: Troubleshooting
  20. robert albrecht
    Thread

    Solved quick stupid question.

    When I use the home button to return the print bed and extruder to it's starting point. Both switches for up and down (y?) should be compressed...
    Thread by: robert albrecht, Feb 23, 2019, 3 replies, in forum: Troubleshooting
Showing results 61 to 80 of 94 Next >
Search Again
Page 4 of 5