1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 9
  1. OutsourcedGuru
    Post

    Request for new Section on forum

    Or... start a github and everyone could push their slicer's profiles into it. Imagine a hierarchy like: * R2 * Cura * Robo * PLA...
    Post by: OutsourcedGuru, Jan 19, 2018 in forum: General Questions
  2. OutsourcedGuru
    Post

    Bad Robo Tape Adhesion

    Ditch the black tape squares as provided by Robo and replace with the BuildTak sheet as provided by Robo or anyone else. I'll never go back to...
    Post by: OutsourcedGuru, Jan 19, 2018 in forum: Troubleshooting
  3. OutsourcedGuru
    Post

    Magnetic print bed attempt

    Correct. I make things complicated compared to how you would do it. Me: "Alexa, please flush". Alexa: "Got it. Flushing the toilet...." But...
    Post by: OutsourcedGuru, Jan 18, 2018 in forum: Mods and Upgrades
  4. OutsourcedGuru
    Post

    Magnetic print bed attempt

    Looks like it's working great. I'll keep this in my arsenal for any thin parts, especially the carbon fiber ones. It works as expected, allowing...
    Post by: OutsourcedGuru, Jan 18, 2018 in forum: Mods and Upgrades
  5. OutsourcedGuru
    Thread

    Magnetic print bed attempt

    I saw something over on the BuildTak website that I thought was cool and wanted to eventually give that a try. In their version they include a...
    Thread by: OutsourcedGuru, Jan 13, 2018, 6 replies, in forum: Mods and Upgrades
  6. OutsourcedGuru
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    I've designed an entirely new filament runout sensor and will install it soon. It's part of my big upgrade to the second extruder. 1. Dual-spool...
    Post by: OutsourcedGuru, Jan 13, 2018 in forum: Troubleshooting
  7. OutsourcedGuru
    Post

    Solved Bed Adhesion, I'm about at my whits end.

    Before I recently dialed in my z-offset (having changed beds and just wanted to print immediately), I used my finger during the first layer to...
    Post by: OutsourcedGuru, Jan 13, 2018 in forum: Troubleshooting
  8. OutsourcedGuru
    Post

    Print Quality issue

    Yeah, get a Skype session going with support so that they can see/hear everything that you showed us.
    Post by: OutsourcedGuru, Jan 13, 2018 in forum: Troubleshooting
  9. OutsourcedGuru
    Post

    Faster startup with 24v

    That was a great write-up, thanks. I've just ordered this one and will use it during my dual-extruder upgrade. (I've been distracted by numerous...
    Post by: OutsourcedGuru, Jan 13, 2018 in forum: Mods and Upgrades
  10. OutsourcedGuru
    Post

    Print Quality issue

    Awesome. Let use know how that turns out. :)
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  11. OutsourcedGuru
    Post

    Solved Print quality when scaling up model

    Wow. If a stepper motor actually had commutator brushes then this would sound exactly like the old-school method of getting an old car's...
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  12. OutsourcedGuru
    Post

    Print Quality issue

    That's... kind of odd. It looks like the carriage is moving around slower than what I'm used to. I'm guessing that blob in the front/right corner...
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  13. OutsourcedGuru
    Post

    Print Quality issue

    And try with a small model like Benchy so that you don't have to waste too much filament.
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  14. OutsourcedGuru
    Post

    Hardened Steel Hot Ends for Carbon Printing

    At the point where I've pulled the trigger on installing that second extruder, I'll changed both nozzles together... or I'll move the worn nozzle...
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: General Questions
  15. OutsourcedGuru
    Post

    Print Quality issue

    Well, that's likely the PLA+, right? If you're getting this at 198 I think I'd drop by 5 at least and re-try.
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  16. OutsourcedGuru
    Post

    Print Quality issue

    Yeah, I was going to say "too hot" as well. I'd try the PLA at 190 and compare.
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  17. OutsourcedGuru
    Post

    Hardened Steel Hot Ends for Carbon Printing

    For what it's worth, I've been printing with carbon fiber (three KG rolls exhausted already) and I've not seen any problems yet on the stock...
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: General Questions
  18. OutsourcedGuru
    Post

    Solved Print quality when scaling up model

    If it were me, I would think about using Blender to scale it and see if it changes the mesh at all. I use Cura and the scaling has never failed...
    Post by: OutsourcedGuru, Jan 11, 2018 in forum: Troubleshooting
  19. OutsourcedGuru
    Post

    Dimensional Accuracy

    I've mentioned this before (mostly a Cura issue, methinks...) For some recent parts (which fit inside 80-20 extruded aluminum rails), it was...
    Post by: OutsourcedGuru, Jan 9, 2018 in forum: Troubleshooting
  20. OutsourcedGuru
    Post

    Found a replacement for the cartridge style thermistor

    [ATTACH]
    Post by: OutsourcedGuru, Jan 9, 2018 in forum: Off Topic
Showing results 41 to 60 of 179 Next >
Search Again
Page 3 of 9