1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Morichalion
    Thread

    I neglected to test the printer before trying to print a basket. Worked out well.

    Replaced the y-axis stepper motor with a stronger one, and turned the stepper driver up a bit (motor is rated for 2 amps, the driver's max is 1.5,...
    Thread by: Morichalion, Feb 3, 2017, 0 replies, in forum: Show and Tell
  2. Morichalion
    Post

    Solved Choosing a replacement motor

    So far as the motor was concerned, my small bit of researched suggested that a larger motor would likely run cooler (the y-axis motor was HOT...),...
    Post by: Morichalion, Feb 1, 2017 in forum: General Questions
  3. Morichalion
    Thread

    Solved Choosing a replacement motor

    The y-axis motor on my r1+ is about dead. Or dying. In any case, the old layer-shift problem is back. I've done the following: Check the belt...
    Thread by: Morichalion, Jan 30, 2017, 5 replies, in forum: General Questions
  4. Morichalion
    Post

    Got my camera set up on my Pi. Funny thing about the first video...

    My whole world shifted..... Maybe the planet's y-axis belt is off again.
    Post by: Morichalion, Jan 29, 2017 in forum: Show and Tell
  5. Morichalion
    Post

    Got my camera set up on my Pi. Funny thing about the first video...

    Yep! I was planning on giving Octoprint a shot next weekend. Maybe.
    Post by: Morichalion, Jan 29, 2017 in forum: Show and Tell
  6. Morichalion
    Thread

    Got my camera set up on my Pi. Funny thing about the first video...

    The first video print I made with it had the camera slowly slip down. I thought it was kinda cool. Also, if anyone's interested in using...
    Thread by: Morichalion, Jan 29, 2017, 3 replies, in forum: Show and Tell
  7. Morichalion
    Post

    Solved Z axis only moves up won't move down

    I had a pretty chronic problem with the z-axis getting knocked around consistently, along with the brackets they sit on. I have a couple of zip...
    Post by: Morichalion, Jan 29, 2017 in forum: Troubleshooting
  8. Morichalion
    Post

    Setting up an R1+ for remote operation

    I tossed a coin and tried Astroprint first. Seems to be working swell so far.
    Post by: Morichalion, Jan 28, 2017 in forum: General Questions
  9. Morichalion
    Thread

    Setting up an R1+ for remote operation

    I have a Raspberry Pi coming in the mail today, it's my first Pi. The goal for this thing is to set up my 3d R1+ for remote operation (mostly I...
    Thread by: Morichalion, Jan 28, 2017, 4 replies, in forum: General Questions
  10. Morichalion
    Post

    Solved Robo3D R1 smoke out back and wont power up

    The computer would be able to see your arduino, even if the power supply was blown. So, since your computer cannot connect to the printer, my...
    Post by: Morichalion, Jan 28, 2017 in forum: Troubleshooting
  11. Morichalion
    Thread

    Are there any command-line 3d printer hosts out there?

    Basically, I'm planning on getting some steppers, some electronics, and some other stuff, and control it with my laptop to make an...
    Thread by: Morichalion, Oct 18, 2016, 0 replies, in forum: Software
  12. Morichalion
    Post

    Discovery from 2001

    Awesome!!
    Post by: Morichalion, Oct 8, 2016 in forum: Show and Tell
  13. Morichalion
    Thread

    I made a little sculpture to test an idea on how to avoid having print-lines show up.

    The basic idea is to set up a very slight displacement on the model so that the roughened surface will mask the look of the printed layers. In...
    Thread by: Morichalion, Oct 8, 2016, 3 replies, in forum: Show and Tell
  14. Morichalion
    Post

    Had a power outage tonight

    Hmm... Maybe that's what happened to mine last night. I was printing a spider-themed medallion thing. I had started it late last night, and...
    Post by: Morichalion, Oct 2, 2016 in forum: Show and Tell
  15. Morichalion
    Post

    Contest to win a C2

    Hmmm.... I just ordered a bunch of LEDs and batteries. Perhaps I can use those for this contest. Thanks for the heads up!
    Post by: Morichalion, Oct 2, 2016 in forum: Off Topic
  16. Morichalion
    Thread

    I've finally fixed my Y-axis shift problem. FOREVER!!!!

    .... or just for now. Probably just for now. Anyway, It's still mildly janky for being fixed. :\ The problem I've been having is that...
    Thread by: Morichalion, Oct 2, 2016, 0 replies, in forum: Show and Tell
  17. Morichalion
    Post

    Solved Is it possible to redefine the points that the autolevel routine uses?

    Wires. ><
    Post by: Morichalion, Oct 1, 2016 in forum: Troubleshooting
  18. Morichalion
    Post

    Solved Is it possible to redefine the points that the autolevel routine uses?

    Yeah, something was where it wasn't supposed to be. Now it's where it's supposed to be. All is well.
    Post by: Morichalion, Oct 1, 2016 in forum: Troubleshooting
  19. Morichalion
    Thread

    Solved Is it possible to redefine the points that the autolevel routine uses?

    I'm running a print to test a fix I made to try and resolve y-axis shift issues. Damn thing is, my fix seems to be running into something during...
    Thread by: Morichalion, Oct 1, 2016, 4 replies, in forum: Troubleshooting
  20. Morichalion
    Post

    Solved Where can I find models for the R1+ parts?

    I do believe I'm being spoiled, Geof. Thank you very much. :)
    Post by: Morichalion, Sep 27, 2016 in forum: General Questions
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2