1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 5
  1. Patrick Ryan
    Post

    Solved Print quality issues after titan upgrade

    So, this is my second attempt with pla. After my first failed attempt I switched out nozzles to make sure it wasn't a clogged nozzle. I was...
    Post by: Patrick Ryan, Jan 23, 2017 in forum: Troubleshooting
  2. Patrick Ryan
    Post

    Solved Print quality issues after titan upgrade

    After putting the pla in and starting the print I noticed that both z axis weren't even. I corrected that so now since I have the pla in there...
    Post by: Patrick Ryan, Jan 23, 2017 in forum: Troubleshooting
  3. Patrick Ryan
    Post

    Solved Print quality issues after titan upgrade

    Haven't tried, I'll give it shot and let you know how it does.
    Post by: Patrick Ryan, Jan 23, 2017 in forum: Troubleshooting
  4. Patrick Ryan
    Thread

    Solved Print quality issues after titan upgrade

    So, I decided to do the Titan upgrade, I followed all the instructions on the wiki and the forum. I calibrated my extruder steps and changed the...
    Thread by: Patrick Ryan, Jan 23, 2017, 14 replies, in forum: Troubleshooting
  5. Patrick Ryan
    Post

    Solved Printer turning off

    Awesome! thanks.
    Post by: Patrick Ryan, Jan 22, 2017 in forum: Troubleshooting
  6. Patrick Ryan
    Post

    Solved Printer turning off

    Cool thanks
    Post by: Patrick Ryan, Jan 22, 2017 in forum: Troubleshooting
  7. Patrick Ryan
    Post

    Solved Printer turning off

    [MEDIA] Here is a video of it happening
    Post by: Patrick Ryan, Jan 22, 2017 in forum: Troubleshooting
  8. Patrick Ryan
    Post

    Solved Printer turning off

    Yeah, that does seem like a feasible possibility. My robo is like 7 months old, do you think this is something I should take up with them?
    Post by: Patrick Ryan, Jan 22, 2017 in forum: Troubleshooting
  9. Patrick Ryan
    Post

    Solved Printer turning off

    Yes
    Post by: Patrick Ryan, Jan 22, 2017 in forum: Troubleshooting
  10. Patrick Ryan
    Thread

    Solved Printer turning off

    Ok, so I have a unique problem. Whenever I preheat using my lcd or do a print and whenever the hot end gets close to the final temp (doesn't...
    Thread by: Patrick Ryan, Jan 21, 2017, 11 replies, in forum: Troubleshooting
  11. Patrick Ryan
    Post

    Y Axis Bearing Alternative

    Does anyone have any other sources for these bushings? It appears that utilibots is out of stock and I'm itching to do this upgrade. I did Google...
    Post by: Patrick Ryan, Jan 20, 2017 in forum: Mods and Upgrades
  12. Patrick Ryan
    Post

    E3D v6 Information, Installation Guides, and Review

    My bad. You are right
    Post by: Patrick Ryan, Sep 24, 2016 in forum: Mods and Upgrades
  13. Patrick Ryan
    Post

    E3D v6 Information, Installation Guides, and Review

    Don't use the v2 firmware. Use the"leadscrew update" firmware. I scratched my head for a long time trying to figure that out
    Post by: Patrick Ryan, Sep 24, 2016 in forum: Mods and Upgrades
  14. Patrick Ryan
    Post

    E3D v6 Information, Installation Guides, and Review

    i ordered that one too. It is not an E3dv6. I emailed back and forth with the sellers but they didn't do anything for me until I contacted Amazon...
    Post by: Patrick Ryan, Sep 16, 2016 in forum: Mods and Upgrades
  15. Patrick Ryan
    Post

    Solved Firmware update troubles

    To fix my issue was to not install version 2 and use version 1 change my settings for the lcd screen. I also had the wires crossed on my screen
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
  16. Patrick Ryan
    Post

    Solved Firmware update troubles

    Got it! Thanks so much guys
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
  17. Patrick Ryan
    Post

    Solved Firmware update troubles

    ok so the leadscrew update compiled and loaded, I commented out the xxl display and uncommented the full graphics but the screen is just blue with...
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
  18. Patrick Ryan
    Post

    Solved Firmware update troubles

    I actually just tried the leadscrew firmware and I think that will work I am doing it primarily for the lcd controller I will let you know if that...
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
  19. Patrick Ryan
    Post

    Solved Firmware update troubles

    I actually just put my preferences to be 'more verbose' during compiling and it looks like all of the files do that with the slashes:(
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
  20. Patrick Ryan
    Post

    Solved Firmware update troubles

    someone in the Arduino forum pointed out that the last two slashes were going the opposite way. would that cause this? is there a way to change...
    Post by: Patrick Ryan, Aug 20, 2016 in forum: Troubleshooting
Showing results 61 to 80 of 83 Next >
Search Again
Page 4 of 5