1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 6
  1. JWW
    Post

    Solved Extruder (locking arm question)

    ... I wonder if the hexagon is indexed in some way and only goes in one way.
    Post by: JWW, Feb 1, 2018 in forum: Troubleshooting
  2. JWW
    Post

    Solved Extruder (locking arm question)

    ... except the wiring is on the wrong side. <g>
    Post by: JWW, Feb 1, 2018 in forum: Troubleshooting
  3. JWW
    Post

    Solved Extruder (locking arm question)

    I've been corresponding with TS for numerous times (via email) and once landline. They are trying to help. I am even more confused than ever now....
    Post by: JWW, Feb 1, 2018 in forum: Troubleshooting
  4. JWW
    Post

    Solved Extruder (locking arm question)

    ... looks like I was totally wrong, sorry about that. Glad I didn't bet my life on it. It appears to me that the very TOP hexagon fin on the...
    Post by: JWW, Jan 31, 2018 in forum: Troubleshooting
  5. JWW
    Post

    Solved Extruder (locking arm question)

    ... thanks for hanging in there with me ... thinking and rechecking.
    Post by: JWW, Jan 31, 2018 in forum: Troubleshooting
  6. JWW
    Post

    Solved Extruder (locking arm question)

    Thanks for the offer, it is appreciated but that's not the problem. The old finned hexagon and the new finned hexagon are the same, measurement...
    Post by: JWW, Jan 31, 2018 in forum: Troubleshooting
  7. JWW
    Post

    Solved Extruder (locking arm question)

    What a PITA. It shouldn't be this way. Something is assembled incorrectly. The pic below explains it the best I can. It's pretty simple to...
    Post by: JWW, Jan 31, 2018 in forum: Troubleshooting
  8. JWW
    Post

    Solved Extruder (locking arm question)

    Still haven't solved the problem. I have talked with tech support so now I'm back here. Here's what I think. Hopefully I can describe the problem...
    Post by: JWW, Jan 30, 2018 in forum: Troubleshooting
  9. JWW
    Post

    Solved Extruder (locking arm question)

    E'gad(s), so hard to explain this problem but I will try again. I am NOT going to use the extruder that has the red gunk on it, so let's eliminate...
    Post by: JWW, Jan 24, 2018 in forum: Troubleshooting
  10. JWW
    Post

    Solved Extruder (locking arm question)

    ... thanks but the problem isn't solved if I do.
    Post by: JWW, Jan 24, 2018 in forum: Troubleshooting
  11. JWW
    Post

    Solved Extruder (locking arm question)

    Thanks trying to help out. I haven't a clue where the bearing is located you mentioned or where the pin might be that you are talking about. The...
    Post by: JWW, Jan 24, 2018 in forum: Troubleshooting
  12. JWW
    Post

    Solved Extruder (locking arm question)

    Pretty simple operation. Open the lever, push the new extruder in, close the lever. When you looked at the new extruder installed you can see it's...
    Post by: JWW, Jan 24, 2018 in forum: Troubleshooting
  13. JWW
    Post

    Solved Extruder (locking arm question)

    Has anyone ever experienced the extruder locking arm scenario I mentioned above? Is there a solution? Thanks, -JW:
    Post by: JWW, Jan 24, 2018 in forum: Troubleshooting
  14. JWW
    Post

    Solved Robo R1 plus - extra parts(?)

    ... that's what I thought. There like 10mm and 15mm inside diameters. The rods are like 8mm.
    Post by: JWW, Jan 22, 2018 in forum: Troubleshooting
  15. JWW
    Thread

    Solved Robo R1 plus - extra parts(?)

    I noticed these two rings laying near the right and left "riser rods" and wondering what they are? One ring was on the left side laying on the...
    Thread by: JWW, Jan 22, 2018, 2 replies, in forum: Troubleshooting
  16. JWW
    Thread

    Solved Extruder (locking arm question)

    I removed and installed a new Robo extruder, which I've done once before about a year ago. I am assuming the thermistor was history but haven't...
    Thread by: JWW, Jan 22, 2018, 48 replies, in forum: Troubleshooting
  17. JWW
    Post

    R1 plus Printing question

    ... thanks.
    Post by: JWW, Jan 21, 2018 in forum: Projects
  18. JWW
    Post

    R1 plus Printing question

    Well I generated supports using MatterControl on the "just_leg_test.stl" (my first picture posted above) to see how they would work with the...
    Post by: JWW, Jan 20, 2018 in forum: Projects
  19. JWW
    Post

    R1 plus Printing question

    Not trying to beat a dead horse to death. I printed the main_body_LS65.stl last night, acquired from the Github link above, with no supports, temp...
    Post by: JWW, Jan 19, 2018 in forum: Projects
  20. JWW
    Post

    R1 plus Printing question

    Before I waste your time Mark, I'll trying printed it again a few times. There's no way I would purchase Simplify3D until I read how to set it up...
    Post by: JWW, Jan 18, 2018 in forum: Projects
Showing results 41 to 60 of 105 Next >
Search Again
Page 3 of 6