1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Archania
    Post

    First test of FLEKS 3D build plate kit

    Think for the clips, people are just using the small binder clips. Unless there is something else. They are the same ones I'm using on my i3 to...
    Post by: Archania, Apr 4, 2016 in forum: Show and Tell
  2. Archania
    Post

    First test of FLEKS 3D build plate kit

    Oh boy. This should be interesting trying it out later today then. Thanks to all and keep all the good/bad info coming!
    Post by: Archania, Apr 1, 2016 in forum: Show and Tell
  3. Archania
    Post

    First test of FLEKS 3D build plate kit

    I'll be getting around to trying out the plate after this long print finishes.
    Post by: Archania, Mar 31, 2016 in forum: Show and Tell
  4. Archania
    Post

    First test of FLEKS 3D build plate kit

    Ouch. So you need to adjust the offset then? Confused now. Some say yes others no. Which is it? And is yes what did you do to insure you didn't...
    Post by: Archania, Mar 31, 2016 in forum: Show and Tell
  5. Archania
    Post

    First test of FLEKS 3D build plate kit

    Just checking to see. That's good then that you don't have to play with the offsets. Thanks
    Post by: Archania, Mar 30, 2016 in forum: Show and Tell
  6. Archania
    Post

    First test of FLEKS 3D build plate kit

    My fleks system will be delivered today. As I have read through the posts, you have to change the z height off set right? Otherwise it will...
    Post by: Archania, Mar 30, 2016 in forum: Show and Tell
  7. Archania
    Post

    First test of FLEKS 3D build plate kit

    Will do that Cbrown. Thanks. Just use to a removable bed. It makes cleaning the plate and removing the print much easier.
    Post by: Archania, Mar 26, 2016 in forum: Show and Tell
  8. Archania
    Post

    First test of FLEKS 3D build plate kit

    How does the zebra plate work out? I ordered a fleks plate system. But still looking for other options.
    Post by: Archania, Mar 26, 2016 in forum: Show and Tell
  9. Archania
    Post

    E3D v6 Information, Installation Guides, and Review

    Oh I have been using it for months for my Prusa i3 and soon to be BigBox. I am just looking at the G-Code beginning and ending scripts to see what...
    Post by: Archania, Mar 26, 2016 in forum: Mods and Upgrades
  10. Archania
    Post

    E3D v6 Information, Installation Guides, and Review

    Thanks Mark. Yet another order to do for E3D lol. Now to figure out Simplify with the Robo...
    Post by: Archania, Mar 26, 2016 in forum: Mods and Upgrades
  11. Archania
    Post

    Just got my Robo 3d r1 plus yesterday Feb 18th. :)

    I just got mine yesterday from Amazon. The SD card is a full one and was taped in on the top piece of foam top insert. Printing like a mad man atm.
    Post by: Archania, Mar 26, 2016 in forum: Show and Tell
  12. Archania
    Post

    E3D v6 Information, Installation Guides, and Review

    Hi there. I just got the Robo 3D R1+ and I am just making sure that it is the 12v as stated on the first page of the E3D v6 that you need. I am...
    Post by: Archania, Mar 25, 2016 in forum: Mods and Upgrades
Showing results 1 to 12 of 12
Search Again