1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. BenJoeM
    Post

    Z Off Set and Delay in Retraction of Extruder at the end

    yes, let me check
    Post by: BenJoeM, Aug 2, 2020 in forum: Troubleshooting
  2. BenJoeM
    Post

    Z Off Set and Delay in Retraction of Extruder at the end

    Thank you. I am using CURA, the original version that came with printer. I have not upgraded the software because when I’ve done in the past I...
    Post by: BenJoeM, Aug 2, 2020 in forum: Troubleshooting
  3. BenJoeM
    Thread

    Z Off Set and Delay in Retraction of Extruder at the end

    Hey, I have had my C2 for sometime and for some reason in the past few months I seem to struggle to get my Z OFF set correct. I do all the...
    Thread by: BenJoeM, Aug 1, 2020, 5 replies, in forum: Troubleshooting
  4. BenJoeM
    Post

    Solved Robo c2 extruder problem

    Tried making sure all sides were balanced, seemed to fix it once I did this.
    Post by: BenJoeM, Jun 2, 2020 in forum: Troubleshooting
  5. BenJoeM
    Thread

    Solved Robo c2 extruder problem

    Hey. Sudden issue. I’ve been printing just fine for weeks when suddenly my latest print the extruder on the right side wants to lift higher than...
    Thread by: BenJoeM, Jun 2, 2020, 3 replies, in forum: Troubleshooting
  6. BenJoeM
    Thread

    Feed Gear works perfectly with Robo C2 Files only

    So looking for some help here. I have now tested 4 filaments and 4 different prints off of the USB drive with. my C2 without issue. But as soon...
    Thread by: BenJoeM, Jun 15, 2018, 2 replies, in forum: Troubleshooting
  7. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Follow up to close this circle with you all! Thanks to @Geof and @mark tomlinson for your tremendous support as always. I purchased a new SD...
    Post by: BenJoeM, Jun 13, 2018 in forum: Troubleshooting
  8. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Correct, I get the blue robo screen then straigh to "UPDATING" and it could stay there for hours, I left it running for 4 hours once.
    Post by: BenJoeM, Jun 11, 2018 in forum: Troubleshooting
  9. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Quick update, A new image was sent to me after they saw my videos, so I burned the image to the SD Card and also sent in photos of the HDMI ends...
    Post by: BenJoeM, Jun 8, 2018 in forum: Troubleshooting
  10. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    So I live in El Salvador, so it is hard to get those parts, when Robo would send it it could take weeks or months to get to me. On the first...
    Post by: BenJoeM, Jun 6, 2018 in forum: Troubleshooting
  11. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Sounds good, I can send you those videos later, it does make contact that was why it baffled everyone you can see it and hear it click but then...
    Post by: BenJoeM, Jun 6, 2018 in forum: Troubleshooting
  12. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Will do, THe second one has other problems altogether the Z-Axis sensor is failing on a software level but works if I manually push it. So I had...
    Post by: BenJoeM, Jun 6, 2018 in forum: Troubleshooting
  13. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Yes I assumed the red was R2. So I was sent 4 images by Tech Support. 2 of my original image both had the EXACT same result as this one, another...
    Post by: BenJoeM, Jun 6, 2018 in forum: Troubleshooting
  14. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    @Jerry RoBo 3D Video 1 - Original Image that was sent with the printer, this gets the reset error and wants me to update. - I plugged it...
    Post by: BenJoeM, Jun 5, 2018 in forum: Troubleshooting
  15. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    I can connect it directly. I will make a short video to show what is happening for clearer understanding. am
    Post by: BenJoeM, Jun 5, 2018 in forum: Troubleshooting
  16. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    I am quoting to ship it tomorrow to see what the cost. Just surprised st the candor of the company to make this right.
    Post by: BenJoeM, Jun 4, 2018 in forum: Troubleshooting
  17. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    This is my second C2. My first one worked for a week, but I live in central America so getting them to send parts and get it fixed took forever....
    Post by: BenJoeM, Jun 4, 2018 in forum: Troubleshooting
  18. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Well at this point Robo has told me to go to hell. So I am stuck with two dead C2s. Most likely will try to sell them for parts at this point.
    Post by: BenJoeM, Jun 4, 2018 in forum: Troubleshooting
  19. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Does that mean they need to send a new printer?
    Post by: BenJoeM, May 26, 2018 in forum: Troubleshooting
  20. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Correct, I have tested all the cables with no luck. Still same issue. New Image has the exact same result on my older C2 that has a z-offset...
    Post by: BenJoeM, May 25, 2018 in forum: Troubleshooting
Showing results 1 to 20 of 39 Next >
Search Again
Page 1 of 2