1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Charlie S
    Post

    Community Favorite E3D v6 Information and Installation Guide

    My E3D heatsink fan came with a long wire with a .1” spacing kk header connector that hooks into the Arduino. I snaked the wire with others and...
    Post by: Charlie S, Jun 15, 2020 in forum: Mods and Upgrades
  2. Charlie S
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Here’s a relatively easy mod to get it up and running. I think these parts are for 2x4’s. The large hole is pretty close to the 12 mm needed for...
    Post by: Charlie S, Apr 28, 2020 in forum: Mods and Upgrades
  3. Charlie S
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Sorry. Another question. I can’t print a quick release part. Can I mod the original quick release to make it work?
    Post by: Charlie S, Apr 27, 2020 in forum: Mods and Upgrades
  4. Charlie S
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Thanks Mark. I messed(cleared jams and assembled wrong and got goop) with the original hot end so much that I finally broke the tiny thermistor...
    Post by: Charlie S, Apr 26, 2020 in forum: Mods and Upgrades
  5. Charlie S
    Post

    RCBF_MESH_PLUS_05-01

    I ditched this idea for now. I’m on 1.1 RC8 ABL. I’LL post another thread of what I’m trying to do and my experience. I really want to get this...
    Post by: Charlie S, Apr 26, 2020 in forum: Mods and Upgrades
  6. Charlie S
    Post

    Community Favorite E3D v6 Information and Installation Guide

    Once you drill the carriage, can the old R1+ extruder be used on the modified carriage with old quick release?
    Post by: Charlie S, Apr 26, 2020 in forum: Mods and Upgrades
  7. Charlie S
    Post

    RCBF_MESH_PLUS_05-01

    I used these commands but the Z number seemed like all values were 4 mm M502 ; only needed if EEPROM hasn’t been initialized M500 ; only needed...
    Post by: Charlie S, Apr 25, 2020 in forum: Mods and Upgrades
  8. Charlie S
    Post

    RCBF_MESH_PLUS_05-01

    Sorry. r1 plus with original parts for now
    Post by: Charlie S, Apr 25, 2020 in forum: Mods and Upgrades
  9. Charlie S
    Post

    better hobbed bolt

    Can you use the Robo extruder motor with the Titan and other extruder?
    Post by: Charlie S, Apr 25, 2020 in forum: Mods and Upgrades
  10. Charlie S
    Post

    RCBF_MESH_PLUS_05-01

    Sorry, I read more and got it to do the probing, but the numbers look wrong
    Post by: Charlie S, Apr 25, 2020 in forum: Mods and Upgrades
  11. Charlie S
    Thread

    RCBF_MESH_PLUS_05-01

    I just loaded this and I can’t get it to do the auto level routine. Any ideas? It just jumps into printing after G29
    Thread by: Charlie S, Apr 24, 2020, 10 replies, in forum: Mods and Upgrades
  12. Charlie S
    Post

    better hobbed bolt

    I guess there is a reason for the name Titan. Seems pretty solid. I just ordered an E3D V6 which I assume can be used with the direct drive Titan
    Post by: Charlie S, Apr 23, 2020 in forum: Mods and Upgrades
  13. Charlie S
    Post

    better hobbed bolt

    Awsome! thanks for the speedy reply Mark
    Post by: Charlie S, Apr 23, 2020 in forum: Mods and Upgrades
  14. Charlie S
    Post

    better hobbed bolt

    Hi good people. I’ve been gaining much insight here.and first thank you sooo much. I think I’m having Hobbed bolt issues. Which one of these is...
    Post by: Charlie S, Apr 23, 2020 in forum: Mods and Upgrades
Showing results 1 to 14 of 14
Search Again