1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Carlos Garcia
    Post

    Solved poor Printing Quality

    For sure I will try, what but I don't know exactly how to.
    Post by: Carlos Garcia, Jan 19, 2019 in forum: Troubleshooting
  2. Carlos Garcia
    Post

    Solved poor Printing Quality

    Yes, its Build Plate Adhesion
    Post by: Carlos Garcia, Jan 19, 2019 in forum: Troubleshooting
  3. Carlos Garcia
    Thread

    Solved poor Printing Quality

    I have tried everything, Aligning rods, unclog hot end Im still getting poor, air print, printing quality. I'm about to throw My printer in the...
    Thread by: Carlos Garcia, Jan 18, 2019, 39 replies, in forum: Troubleshooting
  4. Carlos Garcia
    Thread

    Partial Answer Bad print quality air print

    hello people, hope your all doing well, I’m having trouble with Robo C2 print quality looks like air gaps. Can anybody please help?
    Thread by: Carlos Garcia, Mar 13, 2018, 8 replies, in forum: Troubleshooting
  5. Carlos Garcia
    Post

    Lately I have som Clicking Noise

    Hey Mark, thanks for your reply When you say Doing a "Cold pull" is more problematic you mean it difficult to do or do you mean it could go wrong?...
    Post by: Carlos Garcia, Jun 1, 2017 in forum: General Questions
  6. Carlos Garcia
    Post

    Lately I have som Clicking Noise

    Thank you for your reply, whats an Oiler? I imagine its something I add to the printer so it keeps oiling? where can I get it?
    Post by: Carlos Garcia, Jun 1, 2017 in forum: General Questions
  7. Carlos Garcia
    Thread

    Lately I have som Clicking Noise

    I have done one 24 hour print and a 12 hour print after that and I'm doing a 6 hour print now and Im getting some clicking sounds any idea what...
    Thread by: Carlos Garcia, May 31, 2017, 8 replies, in forum: General Questions
  8. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    How do I go about manually doing that?
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  9. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    Ok done, let me know what you think of this outcome. thanks again!
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  10. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    Will do that! thanks again brother, IOU a Beer.
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  11. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    I see the difference Its more like using a paint brush untested of a ketchup bottle, is this good or should I go lower?
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  12. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    Ok im trying this now my new offset is -8.9, Ill tray the print and let you know.
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  13. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    Ok I have tried this I went two extra clicks after I felt resistance and it still happens less but it happens please look at the video, [MEDIA]...
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  14. Carlos Garcia
    Post

    Sorry if this is a stupid question but why does this happens?

    Im trying this right know thanks a lot
    Post by: Carlos Garcia, May 28, 2017 in forum: General Questions
  15. Carlos Garcia
    Thread

    Sorry if this is a stupid question but why does this happens?

    I have been trying to print a spinner for my girls but this keeps happening, why is ti? Do i have to set something? [MEDIA]
    Thread by: Carlos Garcia, May 27, 2017, 16 replies, in forum: General Questions
  16. Carlos Garcia
    Post

    Gantry Deviation out of the box

    Thanks a lot man you´r the best!
    Post by: Carlos Garcia, May 27, 2017 in forum: Show and Tell
  17. Carlos Garcia
    Post

    Gantry Deviation out of the box

    Mark thanks a lot for your reply, Sending it back would cost more than the unit and shipping together cause I'm over in Panama, so I will try to...
    Post by: Carlos Garcia, May 25, 2017 in forum: Show and Tell
  18. Carlos Garcia
    Thread

    Gantry Deviation out of the box

    Just got my C2 and out of the box u notice the gantry clips weren't on properly and I noticed that the gantry was deviated is this normal? should...
    Thread by: Carlos Garcia, May 24, 2017, 5 replies, in forum: Show and Tell
Find older messages
Showing results 21 to 38 of 38
Search Again
Page 2 of 2