1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 7 of 7
  1. jim3Dbot
    Post

    Aluminum Heated Bed

    The gap appears to be somewhere around 3/8"............Is there a silicone rubber weatherstripping or silicon extruded profile that you can push...
    Post by: jim3Dbot, Feb 6, 2016 in forum: Mods and Upgrades
  2. jim3Dbot
    Post

    Aluminum Heated Bed

    Appreciate..........Thank You
    Post by: jim3Dbot, Feb 6, 2016 in forum: Mods and Upgrades
  3. jim3Dbot
    Post

    Aluminum Heated Bed

    Does the 3mm aluminum rigid enuf? Seems 5mm-6mm would be better..........considering alum. for better heat transfer.......good job...
    Post by: jim3Dbot, Feb 6, 2016 in forum: Mods and Upgrades
  4. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    @WheresWaldo .......Well said, If I fix the brass nuts, maybe via set screws to the x axis's idler arms that will tighten things up a bit, relying...
    Post by: jim3Dbot, Feb 4, 2016 in forum: General Questions
  5. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    Short of expensive ball screws & split nut anti-backlash nuts, I have seen backlash addressed with software that momentarily sped up the motor...
    Post by: jim3Dbot, Feb 4, 2016 in forum: General Questions
  6. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    @WheresWaldo Thanks for your input, much appreciated.......Just a little confused on a few statements? Fixin' the brass nuts to the X carriage,...
    Post by: jim3Dbot, Feb 4, 2016 in forum: General Questions
  7. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    Great you have it dialed in, it is quite maddening until you locate the source of the problem,,,,Good going.......One of these daze, I will print...
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  8. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    This prevents bow'in the glass via the snozzle.........but you still need to be level.........[ATTACH] [ATTACH] [ATTACH]
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  9. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    Thanks Waldo & Schlomo, Y axis is good, X considerable low left side, Yep, I guess I may have been quick on ABL, but I remember reading, over a...
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  10. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    Mark, you fricken nailed it.............
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  11. jim3Dbot
    Post

    R1+ Auto-Level not really accurate

    My oH My oH My..........I just stumbled across your thread..............I have been fighting with auto-level for two 10hr days.....I have printed...
    Post by: jim3Dbot, Feb 3, 2016 in forum: General Questions
  12. jim3Dbot
    Thread

    Differential IR height sensor, Attemptin' Clone....ain't sure of success...now stage 10

    Would be nice to 1/2 the size.......and maybe separate the IR sensors from the electronics...must function with E3D v6 Received parts day one of...
    Thread by: jim3Dbot, Aug 25, 2015, 402 replies, in forum: Mods and Upgrades
Find older messages
Showing results 121 to 132 of 132
Search Again
Page 7 of 7