1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 3 of 4
  1. Spidematt
    Post

    PLA Makergeeks Raptor PLA - high heat

    The makergeek abs I use works well for me around 245 but might need to go higher if it's a large print
    Post by: Spidematt, Jan 25, 2017 in forum: Printing Filament
  2. Spidematt
    Post

    PLA Makergeeks Raptor PLA - high heat

    Here is a pic I have my acceleration down all the way to 500 and my jerk at 10 everything even pinion gears is tight
    Post by: Spidematt, Jan 25, 2017 in forum: Printing Filament
  3. Spidematt
    Post

    PLA Makergeeks Raptor PLA - high heat

    Ok so after the thermal paste and re adding my oiler I now have 1 more benchy to add to the pile and so far not having any problems other that the...
    Post by: Spidematt, Jan 24, 2017 in forum: Printing Filament
  4. Spidematt
    Post

    PLA Makergeeks Raptor PLA - high heat

    What is you're setup I have the e3d v6 and tonight I'm going to try the thermal paste and season the tip but what temp are you using mine just...
    Post by: Spidematt, Jan 24, 2017 in forum: Printing Filament
  5. Spidematt
    Post

    Solved Heated Bed cork sagg

    Thanks guess I should have spent more time in forum
    Post by: Spidematt, Jan 24, 2017 in forum: Troubleshooting
  6. Spidematt
    Post

    Community Favorite Bed Heater - Installing SSR & PID Control Instructions

    Where is a good place to find the ssr?
    Post by: Spidematt, Jan 23, 2017 in forum: Mods and Upgrades
  7. Spidematt
    Post

    PLA Makergeeks Raptor PLA - high heat

    I Have yet to get makergeeks normal pla to print it always gets chewed up or jammed and when i cold pull it it comes out as thin hollow tube. i do...
    Post by: Spidematt, Jan 23, 2017 in forum: Printing Filament
  8. Spidematt
    Thread

    Solved Heated Bed cork sagg

    I noticed that the cork on the bottom side of my glass bed is sagging and not touching the glass is this normal?
    Thread by: Spidematt, Jan 23, 2017, 3 replies, in forum: Troubleshooting
  9. Spidematt
    Post

    Solved Robo3D R1 smoke out back and wont power up

    If it is the version that has led lights unplug it and move the bed back and forth fast with the power turned on if this lights the lights up then...
    Post by: Spidematt, Jan 23, 2017 in forum: Troubleshooting
  10. Spidematt
    Post

    Partially Solved Only prints on half the bed

    this left side switch is turned around compared to mine not sure that it matters but it might .
    Post by: Spidematt, Dec 25, 2016 in forum: Troubleshooting
  11. Spidematt
    Post

    Solved Not calibrating

    I used to get warping a lot as well but I started using hairsprayinstead of glue stick and it seems to hold it down better than glue stick however...
    Post by: Spidematt, Dec 25, 2016 in forum: Troubleshooting
  12. Spidematt
    Post

    OctoPrint Cura profiles?

    Can you not just slice it on cura and save the geode to you're octo print? If you are using the raspberry octoprint I wouldn't use that as a...
    Post by: Spidematt, Dec 24, 2016 in forum: Software
  13. Spidematt
    Post

    E3d v6

    That sucks I was afraid of that all my temp settings I was using are not working and I can't get it to print like it was Sent from my SHIELD...
    Post by: Spidematt, Dec 23, 2016 in forum: General Questions
  14. Spidematt
    Thread

    E3d v6

    I recently bought a robo 3d r1 plus and havent had any issues with it other than the glass bed having a void in it but i got a replacement for it...
    Thread by: Spidematt, Dec 23, 2016, 3 replies, in forum: General Questions
  15. Spidematt
    Post

    Solved extruder bearing

    ok just looked up at the lm8uu post above that is what i was thinking was a bushing so thanks for all youre help
    Post by: Spidematt, Dec 11, 2016 in forum: Troubleshooting
  16. Spidematt
    Post

    Solved extruder bearing

    just realized you said bushing not bearing the ones on the bottom of the carriage on the 2 x axis rods
    Post by: Spidematt, Dec 11, 2016 in forum: Troubleshooting
  17. Spidematt
    Post

    Solved extruder bearing

    [ATTACH]
    Post by: Spidematt, Dec 11, 2016 in forum: Troubleshooting
  18. Spidematt
    Thread

    Solved extruder bearing

    Had a filament jam and noticed that my extruder bearing looks as if it has been tightened to much and is coming apart this machine is only like 3...
    Thread by: Spidematt, Dec 11, 2016, 5 replies, in forum: Troubleshooting
  19. Spidematt
    Post

    Unanswered Z axis switch

    Yea I'm not having any major printing problems it's just concerning cause when it moves up and down the whole switch assembly on the left side has...
    Post by: Spidematt, Nov 30, 2016 in forum: Troubleshooting
  20. Spidematt
    Post

    Unanswered Z axis switch

    Yea it's all tight it's the whole mount that has some play in between the bracket that keeps it close to the carriage so the whole assembly...
    Post by: Spidematt, Nov 29, 2016 in forum: Troubleshooting
Showing results 41 to 60 of 63 Next >
Search Again
Page 3 of 4