1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jerry Normandin
    Thread

    Latest 3D Print project, R/C Hovercraft

    [ATTACH] Here's a Picture of my latest 3D printed project. I put my year old roll of aqua blue test filament to good use. I printed the...
    Thread by: Jerry Normandin, Jan 27, 2019, 1 replies, in forum: Show and Tell
  2. Jerry Normandin
    Post

    Wow..simplify3d and R1+ works well!

    I owned Simplify 3D. My first 3D printer was a Wanhao Duplicator I3. Bought that 2 years ago.
    Post by: Jerry Normandin, May 5, 2018 in forum: Show and Tell
  3. Jerry Normandin
    Post

    I just started my 3d printed r/c aircraft project

    Here's the latest update for my 3dprinted plane. I.got the wings , fuesalage, and stabalizer done. Next ailerons, flaps, and rudder.[ATTACH]
    Post by: Jerry Normandin, Mar 24, 2018 in forum: Show and Tell
  4. Jerry Normandin
    Post

    Answered What Type of Software Does the R1+ Use?

    The best software for me has been Simplify3D. I am building a 3d printed r/c airplane with a 49" wingspan. There are around 200 3d printed...
    Post by: Jerry Normandin, Mar 18, 2018 in forum: Troubleshooting
  5. Jerry Normandin
    Post

    Show us your best Robo 3d print

    [ATTACH] I just finished my Piper Pawnee fuselage. Hopefully the airplane will be ready to fly by April 2018.
    Post by: Jerry Normandin, Feb 19, 2018 in forum: Projects
  6. Jerry Normandin
    Post

    Partial Answer I have to unclog the extruder just about every time I change the filament.

    Thanks. I didn't think it was the printer. I have some spools of filament that are partially used and we're open 7months ago. I didn't print much...
    Post by: Jerry Normandin, Feb 4, 2018 in forum: Troubleshooting
  7. Jerry Normandin
    Post

    Partial Answer I have to unclog the extruder just about every time I change the filament.

    I know. I am not a 3dprinter newbie. I use the temperature reference on the filament print spool as a guide. Not only every brand is different,...
    Post by: Jerry Normandin, Feb 4, 2018 in forum: Troubleshooting
  8. Jerry Normandin
    Post

    I just started my 3d printed r/c aircraft project

    [ATTACH] I rubbed the wheels with alcohol to give them a realistic look. Tires are mounted on the wheels. The fit was tight. I had to use a...
    Post by: Jerry Normandin, Feb 3, 2018 in forum: Show and Tell
  9. Jerry Normandin
    Thread

    Partial Answer I have to unclog the extruder just about every time I change the filament.

    I am printing a r/c control airplane. I am using 4 different colors of filament. I started with my black parts. When done I heated up the...
    Thread by: Jerry Normandin, Feb 3, 2018, 6 replies, in forum: Troubleshooting
  10. Jerry Normandin
    Thread

    I just started my 3d printed r/c aircraft project

    I really like my.R1+. My first version of my.robot Rover chassis is together. Now I just started printing out parts for my 3d printed aircraft....
    Thread by: Jerry Normandin, Feb 2, 2018, 2 replies, in forum: Show and Tell
  11. Jerry Normandin
    Post

    First project printed out. Rosbot Chassis

    The ROSbot is coming together. Motors and encoders are installed.[ATTACH] I have the bot held together with elastics under a heat lamp to help...
    Post by: Jerry Normandin, Jan 31, 2018 in forum: Show and Tell
  12. Jerry Normandin
    Thread

    First project printed out. Rosbot Chassis

    [ATTACH]
    Thread by: Jerry Normandin, Jan 20, 2018, 2 replies, in forum: Show and Tell
  13. Jerry Normandin
    Post

    Opinions on best slicer/user interface for robo3d

    My favorite slicer is Simplify3d Worth the money. I will post my RosBot Rover chassis when done. Next project is a 3dlabprint r/c airplane. I am...
    Post by: Jerry Normandin, Jan 19, 2018 in forum: Software
  14. Jerry Normandin
    Thread

    Wow..simplify3d and R1+ works well!

    I configured Simlify3Dfor my new R1+. Wow! I will post my RoBot Chassis soon. I printed the side panels with both mattercontrol and simplify.....
    Thread by: Jerry Normandin, Jan 19, 2018, 3 replies, in forum: Show and Tell
  15. Jerry Normandin
    Post

    My Robo is going to be busy tomorow. Has anyone here used the entire Z volume ?

    Simplify 3D defaulted to the orientation. I wouldn't print the this laying flat on the bed. It would be difficult to remove. My next attempt...
    Post by: Jerry Normandin, Jan 14, 2018 in forum: Show and Tell
  16. Jerry Normandin
    Post

    My Robo is going to be busy tomorow. Has anyone here used the entire Z volume ?

    The print failed at 90%. The last part when the front end (the top in the build area) failed on the last angle. The bridging failed. The...
    Post by: Jerry Normandin, Jan 13, 2018 in forum: Show and Tell
  17. Jerry Normandin
    Post

    My Robo is going to be busy tomorow. Has anyone here used the entire Z volume ?

    [IMG] 10.5 hours into the print. 6.5hrs to go. Only issues I see with my first large print is the default location for the filament spool...
    Post by: Jerry Normandin, Jan 13, 2018 in forum: Show and Tell
  18. Jerry Normandin
    Post

    My Robo is going to be busy tomorow. Has anyone here used the entire Z volume ?

    The large print is running. The only adjustment I had to make was to reduce the temperature of the print bed from 80C to 60C. The print started...
    Post by: Jerry Normandin, Jan 13, 2018 in forum: Show and Tell
  19. Jerry Normandin
    Thread

    My Robo is going to be busy tomorow. Has anyone here used the entire Z volume ?

    Here's my stl loaded up in Simplify3d. I already generated the gcode and have it loaded up on my Octopi sdcard ready to start in morning....
    Thread by: Jerry Normandin, Jan 12, 2018, 12 replies, in forum: Show and Tell
  20. Jerry Normandin
    Post

    Does anyone here have a working Cura 3.0.4 for R1 Plus ?

    I was impressed with the results that I got with MatterControl and since the company that sells the stl files for the r/c airplane I'm making...
    Post by: Jerry Normandin, Jan 12, 2018 in forum: Software
Showing results 1 to 20 of 26 Next >
Search Again
Page 1 of 2