1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Paladin
    Post

    Solved New RAMPS Board Only Works Plugged Into Computer?

    Old thread, but it solved my problem. I had a spare Ramps board that I used when I replaced the original one when upgrading the heated bed mosfet...
    Post by: Paladin, Mar 14, 2018 in forum: Troubleshooting
  2. Paladin
    Post

    Installing Fans

    I just installed one of the 40mm fan adapters on the hexagon of my R1+ because the stock fan was loud enough to bother me. If you go that route...
    Post by: Paladin, May 20, 2017 in forum: Mods and Upgrades
  3. Paladin
    Post

    Answered Odd filament problem - PLA

    Been printing like a fool on the R1+, so nice to have a working printer! Still working on the kickstarter. I replaced the hobbed bolt and while...
    Post by: Paladin, May 7, 2017 in forum: Troubleshooting
  4. Paladin
    Post

    Robo R1 (Kickstarter) upgrades

    Clear cover is for a filament spool holder. There's an acrylic rod that screws into the clear cover that you put the spool on. I found that out...
    Post by: Paladin, May 6, 2017 in forum: General Questions
  5. Paladin
    Post

    Answered Odd filament problem - PLA

    Well, I now have 2 Robo 3D's! I saw a local ad for another used one but this one was an R1+, not another Kickstarter. After cleaning it up (tons...
    Post by: Paladin, May 2, 2017 in forum: Troubleshooting
  6. Paladin
    Post

    Answered Odd filament problem - PLA

    I raised the hotend and extracted 100mm of filament while watching it. It was definitely not a uniform extrusion. I did it about 5 times and the...
    Post by: Paladin, Apr 26, 2017 in forum: Troubleshooting
  7. Paladin
    Post

    Answered Odd filament problem - PLA

    Replaced the ramps board and now the hotend and bed heat as they should. Still can't print anything without gaps. I tried using heated bed and...
    Post by: Paladin, Apr 24, 2017 in forum: Troubleshooting
  8. Paladin
    Post

    Answered Odd filament problem - PLA

    Don't tell me that, I live in the pacific northwest! I'd only be able to print for the couple weeks of summer we get! Seriously though, I...
    Post by: Paladin, Apr 23, 2017 in forum: Troubleshooting
  9. Paladin
    Post

    Answered Odd filament problem - PLA

    Now that I'm starting to print from SD card on the smart LCD, it's quieter in the room. I've just noticed some popping or snapping sounds. At...
    Post by: Paladin, Apr 23, 2017 in forum: Troubleshooting
  10. Paladin
    Post

    Answered Odd filament problem - PLA

    I added a piece of sponge with some canola oil and it didn't seem to change the behavior. Since I didn't season the nozzle when new, I added a...
    Post by: Paladin, Apr 23, 2017 in forum: Troubleshooting
  11. Paladin
    Post

    Answered Odd filament problem - PLA

    I have not. It is on my list of things to do. Here I printed a spool holder with oiler but I haven't used the oiler. I'll give it a shot!
    Post by: Paladin, Apr 20, 2017 in forum: Troubleshooting
  12. Paladin
    Post

    Answered Odd filament problem - PLA

    All layers. What I was printing in the picture was a case for an LCD display. The problem continued when it finished printing the large flat...
    Post by: Paladin, Apr 20, 2017 in forum: Troubleshooting
  13. Paladin
    Thread

    Answered Odd filament problem - PLA

    First a little background. I bought a used Robo 3D kickstarter and have added auto level, E3D V6 hotend, linear rod Y axis and just installed...
    Thread by: Paladin, Apr 19, 2017, 17 replies, in forum: Troubleshooting
  14. Paladin
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    I finished the install today but haven't calibrated or printed anything yet. I wasn't sure about the movement I have in the lead screws. It...
    Post by: Paladin, Apr 18, 2017 in forum: Mods and Upgrades
  15. Paladin
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    I'm printing the adapters now, and ordered the same TR8*2 lead screws. Care to share your firmware numbers??
    Post by: Paladin, Apr 16, 2017 in forum: Mods and Upgrades
  16. Paladin
    Post

    Yet another bed replacement.

    I just received the same kit yesterday, except I went with the 400mm rods. Looking forward to ditching the drawer slides! Lead screws are on the...
    Post by: Paladin, Apr 6, 2017 in forum: Projects
  17. Paladin
    Post

    Solved Z axis grinding after upgrade

    Sweet! Rather than using the "R1 with Auto Level and 5/16 inch Rods" firmware and having to change the hotend thermistor and max temp settings...
    Post by: Paladin, Apr 1, 2017 in forum: Troubleshooting
  18. Paladin
    Post

    Solved Z axis grinding after upgrade

    Looking at the firmware page, I think I need to use "R1 with Auto Level and 5/16 inch Rods". I think the one I used was for the later 8mm R1's....
    Post by: Paladin, Apr 1, 2017 in forum: Troubleshooting
  19. Paladin
    Post

    Solved Z axis grinding after upgrade

    Getting ready for work this morning, I found a post here with a video of the same grinding sound as my Robo. It seems that there's a chance I...
    Post by: Paladin, Apr 1, 2017 in forum: Troubleshooting
  20. Paladin
    Thread

    Solved Z axis grinding after upgrade

    I just completed some upgrades on my kickstarter Robo 3D. I installed the couplers, brackets and switches today replace the original single Z...
    Thread by: Paladin, Mar 31, 2017, 4 replies, in forum: Troubleshooting
Showing results 1 to 20 of 26 Next >
Search Again
Page 1 of 2