1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    I finally had some time to work on it again this morning. I switched the board back to the original and it's working. Thanks again to everyone for...
    Post by: Randy Merrell, Apr 2, 2019 in forum: Troubleshooting
  2. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    What does it sound like to you? I want to get it working again. I value your advice. You've been so much help in this process.
    Post by: Randy Merrell, Mar 5, 2019 in forum: Troubleshooting
  3. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    So now it touches down 9 places and tries to print about 3 inches in the air. I think the Arduino has the later software. Is there someplace that...
    Post by: Randy Merrell, Mar 5, 2019 in forum: Troubleshooting
  4. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    What did you want to see in the pictures?
    Post by: Randy Merrell, Mar 3, 2019 in forum: Troubleshooting
  5. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    I don't have auto leveling.
    Post by: Randy Merrell, Mar 3, 2019 in forum: Troubleshooting
  6. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    When I bought it the R1 did not have a heated bed, the R!+ had a heated bed. Mine has a heated bed.
    Post by: Randy Merrell, Mar 1, 2019 in forum: Troubleshooting
  7. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    I'll take some pictures. I think I'm ready to start printing. I moved the switch post to the center post. Giving it the opposite effect. I have...
    Post by: Randy Merrell, Mar 1, 2019 in forum: Troubleshooting
  8. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    How would I change that line?
    Post by: Randy Merrell, Feb 28, 2019 in forum: Troubleshooting
  9. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    That sounds like my problem. I was told at the time I was buying a R1+. It was right after the Kickstarter. That explains what happened when I...
    Post by: Randy Merrell, Feb 28, 2019 in forum: Troubleshooting
  10. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    Now my Z stop switch is working opposite of what it should. The Z only moves down when the switch is engaged. Probably something I did while...
    Post by: Randy Merrell, Feb 28, 2019 in forum: Troubleshooting
  11. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    That was it. There was never anything wrong. Just my ignorance. After moving I was just trying to check it out and make sure all the motors...
    Post by: Randy Merrell, Feb 28, 2019 in forum: Troubleshooting
  12. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    Perfect I'll give that a try.
    Post by: Randy Merrell, Feb 28, 2019 in forum: Troubleshooting
  13. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    I think I replaced both the RAMPS and Arduino as they are stacked together. Same condition all other motors (X,Y,Z) work. The extruder motor works...
    Post by: Randy Merrell, Feb 27, 2019 in forum: Troubleshooting
  14. Randy Merrell
    Post

    Solved Stumped! Extruder Problem

    Yes ramps.
    Post by: Randy Merrell, Feb 20, 2019 in forum: Troubleshooting
  15. Randy Merrell
    Thread

    Solved Stumped! Extruder Problem

    Old original R1+. This is strange so hang with me. My extruder stopped. So I searched and found troubleshooting tips. Swapped the connection to...
    Thread by: Randy Merrell, Feb 20, 2019, 33 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again