1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. Mike Toole
    Post

    Unresolved No power to my part cooling fan

    What type of connectors are they? I went to our local electronics store and they had nothing like them. Do you know what the name/type is? Sent...
    Post by: Mike Toole, Jul 5, 2019 in forum: Troubleshooting
  2. Mike Toole
    Post

    Unresolved No power to my part cooling fan

    Well, I ordered a kit and got both boards. Should I change out both? I have never loaded firmware which I believe will be necessary. I also...
    Post by: Mike Toole, Jul 5, 2019 in forum: Troubleshooting
  3. Mike Toole
    Post

    Unresolved No power to my part cooling fan

    I will tear down and inspect this weekend. Thanks!! Sent from my iPhone using Tapatalk
    Post by: Mike Toole, May 20, 2019 in forum: Troubleshooting
  4. Mike Toole
    Post

    Unresolved No power to my part cooling fan

    What about this one? Longruner 3D Printer Kit RAMPS 1.4 Controller Board + 5pcs A4988 StepStick Stepper Motor Driver Module + Heat Sink for 3D...
    Post by: Mike Toole, May 20, 2019 in forum: Troubleshooting
  5. Mike Toole
    Post

    Unresolved No power to my part cooling fan

    Yes. In the control panel I turned it to 100% after the second layer and nothing. I plugged the part fan into the extruded fan and the fan works....
    Post by: Mike Toole, May 19, 2019 in forum: Troubleshooting
  6. Mike Toole
    Thread

    Unresolved No power to my part cooling fan

    I noticed the fan was not running so I unplugged it and checked for voltage. None. any ideas where to next?
    Thread by: Mike Toole, May 18, 2019, 11 replies, in forum: Troubleshooting
  7. Mike Toole
    Post

    Solved Affordable options for J-head replacement

    Ok. Thank you. On kind of the same topic, the wire broke off of my thermistor. I would think it is what people are referring to as a “stud”...
    Post by: Mike Toole, Dec 27, 2018 in forum: General Questions
  8. Mike Toole
    Post

    Solved Affordable options for J-head replacement

    Is the https://www.amazon.com/gp/product/B07B4FHN72/ref=ask_ql_qh_dp_hza plug and play?
    Post by: Mike Toole, Dec 23, 2018 in forum: General Questions
  9. Mike Toole
    Post

    ABS layer adhesion issues

    PLA is too rigid for what I’m making. ABS is usually tougher than PLA while being slightly more flexible. Toughness with some flexibility is what...
    Post by: Mike Toole, Mar 12, 2018 in forum: Printing Filament
  10. Mike Toole
    Post

    ABS layer adhesion issues

    Thanks Mark! I will adjust
    Post by: Mike Toole, Mar 11, 2018 in forum: Printing Filament
  11. Mike Toole
    Thread

    ABS layer adhesion issues

    ROBO R1+ Hatchbox Black ABS 245 degrees extrusion temp 80 degree bed temp fan off Printer cloth enclosed. I would prefer ABS for finish part...
    Thread by: Mike Toole, Mar 11, 2018, 7 replies, in forum: Printing Filament
  12. Mike Toole
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Thanks for the inputs. [emoji846]. I will not fix what is not broken. [emoji6] Sent from my iPhone using Tapatalk
    Post by: Mike Toole, Feb 18, 2018 in forum: Mods and Upgrades
  13. Mike Toole
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Total newb here. My Robo R1+ has been printing parts consistently since I received it. As far as I know, things are working ok. Do I need to...
    Post by: Mike Toole, Feb 18, 2018 in forum: Mods and Upgrades
  14. Mike Toole
    Post

    Possible file issue

    Well, this time the problem area is 2.5-3” above the bed. I cleaned and lubed all axis rods. Cold pulled the nozzle a few times. It extrudes...
    Post by: Mike Toole, Oct 22, 2017 in forum: General Questions
  15. Mike Toole
    Post

    Possible file issue

    Ok. I will do that this morning then reprint. Thanks, MT Sent from my iPhone using Tapatalk
    Post by: Mike Toole, Oct 20, 2017 in forum: General Questions
  16. Mike Toole
    Post

    Possible file issue

    Need to clarify. Filament is no longer jamming. I’m just having layer separation/bonding issues in this area. Sent from my iPhone using Tapatalk
    Post by: Mike Toole, Oct 19, 2017 in forum: General Questions
  17. Mike Toole
    Post

    Possible file issue

    Well, looks like it’s repeatable. At the 3.25” to 4” heights. Seems to print fine above and below. Any ideas as to what mechanic issues I might...
    Post by: Mike Toole, Oct 19, 2017 in forum: General Questions
  18. Mike Toole
    Post

    Anyone feel like sharing some pics!!

    These are the trophies I printed for our fantasy football league. [IMG] Sent from my iPhone using Tapatalk
    Post by: Mike Toole, Oct 19, 2017 in forum: Show and Tell
  19. Mike Toole
    Post

    Solved Temperature FALL Error

    or just leave the fan set @ 65% and call it good. lol.
    Post by: Mike Toole, Oct 15, 2017 in forum: Troubleshooting
  20. Mike Toole
    Post

    Solved Temperature FALL Error

    Then yes, I most likely did it wrong. I installed the nozzle into the heat block fully first. then I installed the heat break until it bottomed....
    Post by: Mike Toole, Oct 15, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 52 Next >
Search Again
Page 1 of 3