1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Hellsbells17
    Post

    Dual Extruder Kit Updates?

    Well that really sucks. I bought this printer with the intentions that it would eventually be a dual extruder. If there is not hope for that...
    Post by: Hellsbells17, Mar 13, 2018 in forum: Mods and Upgrades
  2. Hellsbells17
    Post

    Turn Version 1 Bed Heater into a Version 2 Bed Heater

    So the bed is not removable?
    Post by: Hellsbells17, Mar 13, 2018 in forum: Mods and Upgrades
  3. Hellsbells17
    Post

    Turn Version 1 Bed Heater into a Version 2 Bed Heater

    I must be lacking behind. What is the version 2 bed heater?
    Post by: Hellsbells17, Mar 13, 2018 in forum: Mods and Upgrades
  4. Hellsbells17
    Thread

    Dual Extruder Kit Updates?

    Has anybody heard any updates on the dual extruder kit that is supposed to be coming out for the R2?
    Thread by: Hellsbells17, Mar 13, 2018, 35 replies, in forum: Mods and Upgrades
  5. Hellsbells17
    Thread

    Helper Material

    Is there a way to eliminate the printing of what is called "helper" material?
    Thread by: Hellsbells17, Mar 9, 2018, 1 replies, in forum: General Questions
  6. Hellsbells17
    Post

    Sloppy Belt

    This belt has enough slop I can gently push down and it touches the other side of the loop. The other belt has no slop.
    Post by: Hellsbells17, Nov 19, 2017 in forum: Troubleshooting
  7. Hellsbells17
    Thread

    MatterHackers ProFlex TPE

    Has anybody had any success printing with MatterHackers ProFlex TPE? Tried but can't get it to print.
    Thread by: Hellsbells17, Nov 19, 2017, 2 replies, in forum: General Questions
  8. Hellsbells17
    Thread

    Sloppy Belt

    One of the two top belts has a lot of slop in it. Is there a way to tighten it and remove the slop?
    Thread by: Hellsbells17, Nov 19, 2017, 5 replies, in forum: Troubleshooting
  9. Hellsbells17
    Post

    Teflon Filament

    Is it equivalent to ABS?
    Post by: Hellsbells17, Sep 14, 2017 in forum: General Questions
  10. Hellsbells17
    Post

    Teflon Filament

    Anybody used any of the materials from MatterHackers?
    Post by: Hellsbells17, Sep 14, 2017 in forum: General Questions
  11. Hellsbells17
    Post

    Teflon Filament

    Has anybody used Taulman t-glase?
    Post by: Hellsbells17, Sep 14, 2017 in forum: General Questions
  12. Hellsbells17
    Post

    Teflon Filament

    What brand nylon and abs filaments do you use?
    Post by: Hellsbells17, Sep 13, 2017 in forum: General Questions
  13. Hellsbells17
    Thread

    Teflon Filament

    Has anybody used any teflon filaments on the R2?
    Thread by: Hellsbells17, Sep 13, 2017, 14 replies, in forum: General Questions
  14. Hellsbells17
    Post

    Squeaky R2

    I ended up dripping some liquid teflon on the pulleys and the squeaking went away.
    Post by: Hellsbells17, Aug 14, 2017 in forum: Troubleshooting
  15. Hellsbells17
    Thread

    Squeaky R2

    Brand new only on the third print and it is starting to squeak very bad. Can make out the location yet. [MEDIA]
    Thread by: Hellsbells17, Aug 14, 2017, 2 replies, in forum: Troubleshooting
  16. Hellsbells17
    Thread

    Had high hopes but......

    Had high hopes for the R2 but it turnes out to be horrible as the original Robo. :( [IMG]
    Thread by: Hellsbells17, Aug 13, 2017, 3 replies, in forum: Troubleshooting
  17. Hellsbells17
    Thread

    Camera Setting

    I been turning the camera setting to on but then later is back off. Is there a permanent on setting?
    Thread by: Hellsbells17, Aug 11, 2017, 3 replies, in forum: Software
  18. Hellsbells17
    Thread

    Filament Has Run Out

    Just set up my new R2 and did all the set up but everytime I go to print a part it starts then says "Filament Has Run Out". Any suggestions?
    Thread by: Hellsbells17, Aug 10, 2017, 2 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 38 of 38
Search Again
Page 2 of 2