1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 3
  1. wthierry
    Post

    Bed not heating for ABS

    Calling and asking for tier 2 doesnt work, you need to schedule your call online for that.
    Post by: wthierry, Jul 31, 2017 in forum: Troubleshooting
  2. wthierry
    Post

    Bed not heating for ABS

    I have a fix thats working for me: see this thread:...
    Post by: wthierry, Jul 31, 2017 in forum: Troubleshooting
  3. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Has anyone else tried this except me? I am happy with the result.
    Post by: wthierry, Jul 31, 2017 in forum: Troubleshooting
  4. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Good news, I heated it up to 90 like a champ, and its plugging away now on a print! Thanks guys for your help. Hope some of the others with heat...
    Post by: wthierry, Jul 29, 2017 in forum: Troubleshooting
  5. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Damn, Im a software engineer, and didnt notice he changed the pins. I was all obsessed about the PWM setting and the timeout.... reversed this...
    Post by: wthierry, Jul 29, 2017 in forum: Troubleshooting
  6. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Sorry to be clueless, but what is PWM and why should I keep it enabled? thanks wes
    Post by: wthierry, Jul 29, 2017 in forum: Troubleshooting
  7. wthierry
    Thread

    After reflashing, do you need to re-run the bed leveling wizards?

    just asking.
    Thread by: wthierry, Jul 28, 2017, 1 replies, in forum: Troubleshooting
  8. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    hmm, ok, I can heat the bed up now, but now the zaxis wont raise :( So going back to the old version....
    Post by: wthierry, Jul 28, 2017 in forum: Troubleshooting
  9. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Im pretty sure its the timeout combined with not enough power getting to the heated bed. I can get above 90 now, but it starts struggling to get...
    Post by: wthierry, Jul 28, 2017 in forum: Troubleshooting
  10. wthierry
    Post

    Heat bed problem possibly solved??? Maybe... Partly

    Well I managed to get to above 92 then it happened again. So progress, but not yet perfect....
    Post by: wthierry, Jul 28, 2017 in forum: Troubleshooting
  11. wthierry
    Thread

    Heat bed problem possibly solved??? Maybe... Partly

    Sorry to start another Heat bed thread, But I was able to somewhat solve it without changing out my board, or re wiring it. I took the tips from...
    Thread by: wthierry, Jul 28, 2017, 10 replies, in forum: Troubleshooting
  12. wthierry
    Post

    Bed Can't Get Above 90Deg Before Error

    Looks like their VP of engineering commited you change of 255 to the repository a couple days ago. I am going to try it....
    Post by: wthierry, Jul 28, 2017 in forum: Troubleshooting
  13. wthierry
    Post

    Bed Can't Get Above 90Deg Before Error

    Hmm, now my bed cant even get to 85.... seems to be getting worse..... Recv: ok T:20.3 /0.0 B:73.6 /85.0 @:0 B@:100 Recv: Error:Heating failed,...
    Post by: wthierry, Jul 28, 2017 in forum: Troubleshooting
  14. wthierry
    Post

    Heated bed cant get to 100 degrees?

    havent been able to get through to support in a few days. Anyone have an update on this issue?
    Post by: wthierry, Jul 26, 2017 in forum: Troubleshooting
  15. wthierry
    Post

    Hmm.. printing slanted..

    its doing better now, but need to keep an eye on those set screws.... some are hard to get at. Other than that its printing away a large project...
    Post by: wthierry, Jul 26, 2017 in forum: Troubleshooting
  16. wthierry
    Post

    Hmm.. printing slanted..

    Test print done[IMG] Sent from my Pixel XL using Tapatalk
    Post by: wthierry, Jul 26, 2017 in forum: Troubleshooting
  17. wthierry
    Post

    Hmm.. printing slanted..

    Put it back (took me an hour, the angles are horrible, next time will take the thing apart!) Didnt have any loctite so will have to deal with it...
    Post by: wthierry, Jul 25, 2017 in forum: Troubleshooting
  18. wthierry
    Post

    Hmm.. printing slanted..

    Here is a first look, missing set screw, I can hear it rolling around in the bottom. have to find it [IMG]
    Post by: wthierry, Jul 25, 2017 in forum: Troubleshooting
  19. wthierry
    Post

    Hmm.. printing slanted..

    First look, one fell out. Gotta find it.
    Post by: wthierry, Jul 25, 2017 in forum: Troubleshooting
  20. wthierry
    Post

    Hmm.. printing slanted..

    Here is a pic of it in the machine. here is a pic from inside the machine. this is a new print, seems to be leaning more. X axis possibly?
    Post by: wthierry, Jul 25, 2017 in forum: Troubleshooting
Showing results 21 to 40 of 56 Next >
Search Again
Page 2 of 3