1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Jeff Uberstine
    Post

    R2 Shipping update?

    @mark tomlinson Is there any way you can create a Robo R2 area in the forums, so R2 posts don't need to go in the C2 section?
    Post by: Jeff Uberstine, Feb 10, 2017 in forum: General Questions
  2. Jeff Uberstine
    Post

    Anyone try 20 microns yet?

    Sounds good. I've done 60 microns prints and they come out fine. I'll do a 40 micron next and if that goes well, do a 20 micron. Will post images...
    Post by: Jeff Uberstine, Feb 10, 2017 in forum: Show and Tell
  3. Jeff Uberstine
    Post

    Anyone try 20 microns yet?

    I was asking more if anyone has done it on a C2, Not R1. I can't seem to find any prints on a C2 of that RES. Am I missing something @mark...
    Post by: Jeff Uberstine, Feb 10, 2017 in forum: Show and Tell
  4. Jeff Uberstine
    Thread

    Anyone try 20 microns yet?

    Based on the printer specs, the printer is capable of 20 micron prints, which is virtually SLA quality. Anyone given it a try yet?
    Thread by: Jeff Uberstine, Feb 10, 2017, 19 replies, in forum: Show and Tell
  5. Jeff Uberstine
    Post

    Safe to update Octoprint?

    That seems To be about it. It's just base software and bundled plugins. Sent from my iPhone using Tapatalk
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  6. Jeff Uberstine
    Post

    Safe to update Octoprint?

    That was a change log from the Robo LCD 1.3.1. That said, it looks like 1.3.1 is still in beta but I didn't have any issues with the update.
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  7. Jeff Uberstine
    Post

    Safe to update Octoprint?

    Could it be this? 1.3.1 (2017-2-4) Bug Fixes Fixed issue where updating through the webapp would break future upgrades
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  8. Jeff Uberstine
    Post

    Safe to update Octoprint?

    After that update, you robo found firmware 1.1.1 and was able to update to it without issue. [ATTACH]
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  9. Jeff Uberstine
    Post

    Safe to update Octoprint?

    Screw it, i'm just going to bulk update it all. Seems like the right move here. If not, I'm sure robo can get me sorted.
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  10. Jeff Uberstine
    Post

    Safe to update Octoprint?

    Seems to me that this is the only safe way to update but have not tried it yet @ammulder. If I got to updates in Utilities / Update, I just get an...
    Post by: Jeff Uberstine, Feb 7, 2017 in forum: Software
  11. Jeff Uberstine
    Post

    Safe to update Octoprint?

    @ammulder Any issues so far?
    Post by: Jeff Uberstine, Feb 5, 2017 in forum: Software
  12. Jeff Uberstine
    Post

    C2, Camera addition

    That STL file is just a long rectangle looking thing. @STEM_Steve Can you check out if another file is needed and provide it?
    Post by: Jeff Uberstine, Feb 3, 2017 in forum: Show and Tell
  13. Jeff Uberstine
    Post

    ROBO C2 Nothing But Problems

    I just brought up BB because virtually every time I have something large and heavy shipped from them, it arrives damaged. Note, this means shipped...
    Post by: Jeff Uberstine, Jan 26, 2017 in forum: Show and Tell
  14. Jeff Uberstine
    Post

    C2, Camera addition

    Your STL file looks like it's only one piece. Where are the other pieces you used? Sent from my iPhone using Tapatalk
    Post by: Jeff Uberstine, Jan 25, 2017 in forum: Show and Tell
  15. Jeff Uberstine
    Post

    ROBO C2 Nothing But Problems

    Hey Mark. That is a real bummer :(. My C2 has been nothing but flawless but I bought it from amazon. Is there handle chance that the issue might...
    Post by: Jeff Uberstine, Jan 25, 2017 in forum: Show and Tell
  16. Jeff Uberstine
    Post

    New C2 works GREAT

    Yep, I just wanted to post this because when I was considering it, the one and only review I could find sounded really bad. That said, I trust the...
    Post by: Jeff Uberstine, Jan 25, 2017 in forum: Show and Tell
  17. Jeff Uberstine
    Thread

    Safe to update Octoprint?

    Is it safe to update Octoprint on their Web UI directly or will it cause major issues?
    Thread by: Jeff Uberstine, Jan 25, 2017, 25 replies, in forum: Software
  18. Jeff Uberstine
    Thread

    New C2 works GREAT

    I just wanted to report that I just got my C2 and it works great. I know Amazon has 1 review of the C2 and it is negative and there is a video on...
    Thread by: Jeff Uberstine, Jan 25, 2017, 2 replies, in forum: Show and Tell
Find older messages
Showing results 21 to 38 of 38
Search Again
Page 2 of 2