1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. danjomite
    Post

    Print head clicking

    Cleaning the nozzle didn't fix it. I did find that the nozzle extrusion hole is slightly bent so it's not perfectly round (almost D shaped). Not...
    Post by: danjomite, Aug 24, 2017 in forum: Troubleshooting
  2. danjomite
    Post

    R2 Click and Snapping Sounds

    Figured I'd try it because at this point what's the worst that could happen lol. Thanks for the settings, I'll set them for the next print after...
    Post by: danjomite, Aug 23, 2017 in forum: Troubleshooting
  3. danjomite
    Post

    R2 Click and Snapping Sounds

    Disabled retraction and got the following print. Will try cleaning the nozzle next. [IMG] [IMG] [IMG]
    Post by: danjomite, Aug 23, 2017 in forum: Troubleshooting
  4. danjomite
    Post

    Print head clicking

    I'll try that next! At the moment I've tried increasing the retraction minimum distance and will see how it goes.
    Post by: danjomite, Aug 22, 2017 in forum: Troubleshooting
  5. danjomite
    Post

    Print head clicking

    Oh okay, fair enough. So at this point what are my options? It certainly doesn't seem like the printer is functioning normally. Can I slow down...
    Post by: danjomite, Aug 22, 2017 in forum: Troubleshooting
  6. danjomite
    Post

    Print head clicking

    I do print with PLA. It tends to clog up with "lower" temperatures, but as I said if I do keep it at higher temps, it will work fine. That's...
    Post by: danjomite, Aug 22, 2017 in forum: Troubleshooting
  7. danjomite
    Post

    Print head clicking

    Sorry I should have said E3D V6 hotend.
    Post by: danjomite, Aug 22, 2017 in forum: Troubleshooting
  8. danjomite
    Post

    R2 Click and Snapping Sounds

    I'm having the same issue. Did you just resolve it by setting the Z offset a bit higher? I've been forced to do prints with PLA at about 220+...
    Post by: danjomite, Aug 22, 2017 in forum: Troubleshooting
  9. danjomite
    Post

    Print head clicking

    Just wanted to report back with an update: I did build a temporary stand for the filament and it didn't fix the issue. Increasing the nozzle...
    Post by: danjomite, Aug 8, 2017 in forum: Troubleshooting
  10. danjomite
    Post

    R2 Bed Temp

    I was also having this issue and then I cranked the B value in the EEPROM up to 30000 as someone suggested and it starts to print at around 79.3...
    Post by: danjomite, Jun 18, 2017 in forum: Troubleshooting
  11. danjomite
    Post

    Print head clicking

    Ah okay, I was wondering what back pressure meant. I'll try some sort of temporary setup at least then and see because you may be right.
    Post by: danjomite, Jun 15, 2017 in forum: Troubleshooting
  12. danjomite
    Post

    Print head clicking

    Agreed. I got the R1 Kickstarter edition and it took me a ton of time before I got it configured and working properly, and I definitely did have...
    Post by: danjomite, Jun 15, 2017 in forum: Troubleshooting
  13. danjomite
    Post

    Print head clicking

    Thanks everyone for the responses, I am going to try and build a filament holder to suspend the spool above the printer and feed it through a much...
    Post by: danjomite, Jun 15, 2017 in forum: Troubleshooting
  14. danjomite
    Thread

    Print head clicking

    Hello, I just wanted to post this issue as it has been happening for me every once in a while and it has ruined longer prints: The print head...
    Thread by: danjomite, Jun 14, 2017, 26 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again